Explanation Consider the system is in steady state. Hence, the inlet and exit mass flow rates are equal. The mass flow rate of feed water ( m ˙ f w ) is as follows. m ˙ 1 = m ˙ 2 = m ˙ f w The mass flow rate of steam ( m ˙ s ) is as follows. m ˙ 3 = m ˙ 4 = m ˙ s Write the energy rate balance equation for one inlet and one outlet system. [ Q ˙ 1 + W ˙ 1 + m ˙ ( h 1 + V 1 2 2 + g z 1 ) ] − [ Q ˙ 2 + W ˙ 2 + m ˙ ( h 2 + V 2 2 2 + g z 2 ) ] = Δ E ˙ system (I) Here, the rate of heat transfer is Q ˙ , the rate of work transfer is W ˙ , the enthalpy is h and the velocity is V , the gravitational acceleration is g , the elevation from the datum is z and the rate of change in net energy of the system is Δ E ˙ system ; the suffixes 1 and 2 indicates the inlet and outlet of the system. The system is at steady state. Hence, the rate of change in net energy of the system becomes zero. Δ E ˙ system = 0 Neglect the work transfer, heat transfer to the surrounding, potential and kinetic energies. The Equations (I) reduced as follows for feed water. [ 0 + 0 + m ˙ 1 ( h 1 + 0 + 0 ) ] − [ 0 + 0 + m ˙ 2 ( h 2 + 0 + 0 ) ] = 0 m ˙ 1 h 1 − m ˙ 2 h 2 = 0 m ˙ 1 h 1 = m ˙ 2 h 2 (II) The Equations (I) reduced as follows for steam. [ 0 + 0 + m ˙ 3 ( h 3 + 0 + 0 ) ] − [ 0 + 0 + m ˙ 4 ( h 4 + 0 + 0 ) ] = 0 m ˙ 3 h 3 − m ˙ 4 h 4 = 0 m ˙ 3 h 3 = m ˙ 4 h 4 (III) Combining Equation (II) and (III). m ˙ 1 h 1 + m ˙ 3 h 3 = m ˙ 2 h 2 + m ˙ 4 h 4 m ˙ 2 h 2 − m ˙ 1 h 1 = m ˙ 3 h 3 − m ˙ 4 h 4 Substitute m ˙ f w for m ˙ 1 , m ˙ 2 and m ˙ s for m ˙ 3 , m ˙ 4

Thermodynamics: An Engineering Approach ( 9th International Edition ) ISBN:9781260092684

9th Edition

ISBN: 9781260048667

Author: Yunus A. Cengel Dr.; Michael A. Boles

Publisher: McGraw-Hill Education

See similar textbooks

Videos

Question

Chapter 10.9, Problem 94RP

To determine

The rate at which bleed steam is required.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 10.9, Problem 93P

Chapter 10.9, Problem 95RP

Students have asked these similar questions

Consider a simple ideal Brayton cycle with air as the working fluid. The pressure ratio of the cycle is 7.2, and the minimum and maximum temperatures are 300 K and 1350 K, respectively. Now the pressure ratio is doubled without changing the minimum and the maximum temperatures in the cycle. Assuming constant specific heats for air at room temperature; show the initial process and process change in a T-s diagram; calculate the change in the net work output per unit mass; and determine the change in thermal efficiency of the cycle.

In a regenerative Rankine cycle. the closed feedwater heater with a pump as shown in the figure is arranged so that the water at state 5 is mixed with the water at state 2 to form a feedwater, which is a saturated liquid at 200 psia. Feedwater enters this heater at 350°F and 200 psia with a flow rate of 3 lbm/s. The bleed steam is taken from the turbine at 160 psia and 400°F and enters the pump as a saturated liquid at 160 psia. Determine the mass flow rate of the bleed steam required to operate this unit. Use steam tables. Feedwater Bleed steam (from turbine) 1 —¬ The mass flow rate of the bleed steam required to operate the unit is lbm/s.

In a Rankine cycle with reheating, the steam leaves the boiler at 2.5 MPa and 600 ºC and enters the high-pressure turbine where it expands to a pressure of 1 MPa to be then subjected to a reheating process from where it leaves at 1 MPa and 600 ° C. The steam at these conditions enters the low-pressure turbine and expands up to the condenser pressure of 50 kPa. The heat that is extracted in the condenser is 1500 kJ / s. If the adiabatic efficiency of the turbines and the pump is 95%, determine the total heat flow in kJ / s delivered to the boiler.

Chapter 10 Solutions

Thermodynamics: An Engineering Approach ( 9th International Edition ) ISBN:9781260092684

Ch. 10.9 - Why is the Carnot cycle not a realistic model for...Ch. 10.9 - Why is excessive moisture in steam undesirable in...Ch. 10.9 - A steady-flow Carnot cycle uses water as the...Ch. 10.9 - A steady-flow Carnot cycle uses water as the...Ch. 10.9 - Consider a steady-flow Carnot cycle with water as...Ch. 10.9 - Water enters the boiler of a steady-flow Carnot...Ch. 10.9 - What four processes make up the simple ideal...Ch. 10.9 - Consider a simple ideal Rankine cycle with fixed...Ch. 10.9 - Consider a simple ideal Rankine cycle with fixed...Ch. 10.9 - Consider a simple ideal Rankine cycle with fixed...

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

The rate at which bleed steam is required.

Solution Summary: The author explains the rate at which bleed steam is required and the energy rate balance equation for one inlet and one outlet system.

Videos

The rate at which bleed steam is required.

Want to see the full answer?

Chapter 10 Solutions