Concept explainers
When tightening a bolt, mechanics sometimes extend the length of a wrench handle by slipping a section of pipe over the handle. Why could this procedure easily damage the bolt?
The reason for which extending the length of a wrench handle by slipping a section of pipe over the handle make the bolt damage easily.
Answer to Problem 1CQ
The increased length of the wrench handle results the increased torque to act on the bolt, which in turn shear and damage the bolt.
Explanation of Solution
The length of the wrench handle and the torque applied on the bolt is directly proportional. Increasing the length of the wrench handle will increase the torque being applied on the bolt.
This occurs due to the increase in the moment arm while increasing the length of the wrench handle.
The bolt is designed to withstand a particular amount of torque applied on it. The increased torque due to the increased length of the wrench handle will shear the bolt.
Want to see more full solutions like this?
Chapter 10 Solutions
College Physics (10th Edition)
Additional Science Textbook Solutions
Sears And Zemansky's University Physics With Modern Physics
Cosmic Perspective Fundamentals
Physics for Scientists and Engineers with Modern Physics
Conceptual Physics (12th Edition)
Glencoe Physical Science 2012 Student Edition (Glencoe Science) (McGraw-Hill Education)
- The fishing pole in Figure P10.22 makes an angle of 20.0 with the horizontal. What is the torque exerted by the fish about an axis perpendicular to the page and passing through the anglers hand if the fish pulls on the fishing line with a force F=100N at an angle 37.0 below the horizontal? The force is applied at a point 2.00 m from the anglers hands. Figure P10.22arrow_forwardA force of F=(2.00i+3.00j) N is applied to an object that is pivoted about a fixed axle aligned along the z coordinate axis. The force is applied at the point r=(4.00i+5.00j)m. Find (a) the magnitude of the net torque about the z axis and (b) the direction of the torque vector .arrow_forwardA uniform beam resting on two pivots has a length L = 6.00 m and mass M = 90.0 kg. The pivot under the left end exerts a normal force n1 on the beam, and the second pivot located a distance = 4.00 m from the left end exerts a normal force n2. A woman of mass m = 55.0 kg steps onto the left end of the beam and begins walking to the right as in Figure P10.28. The goal is to find the womans position when the beam begins to tip. (a) What is the appropriate analysis model for the beam before it begins to tip? (b) Sketch a force diagram for the beam, labeling the gravitational and normal forces acting on the beam and placing the woman a distance x to the right of the first pivot, which is the origin. (c) Where is the woman when the normal force n1 is the greatest? (d) What is n1 when the beam is about to tip? (e) Use Equation 10.27 to find the value of n2 when the beam is about to tip. (f) Using the result of part (d) and Equation 10.28, with torques computed around the second pivot, find the womans position x when the beam is about to tip. (g) Check the answer to part (e) by computing torques around the first pivot point. Figure P10.28arrow_forward
- A stepladder of negligible weight is constructed as shown in Figure P10.73, with AC = BC = ℓ. A painter of mass m stands on the ladder a distance d from the bottom. Assuming the floor is frictionless, find (a) the tension in the horizontal bar DE connecting the two halves of the ladder, (b) the normal forces at A and B, and (c) the components of the reaction force at the single hinge C that the left half of the ladder exerts on the right half. Suggestion: Treat the ladder as a single object, but also treat each half of the ladder separately. Figure P10.73 Problems 73 and 74.arrow_forwardConsider the disk in Problem 71. The disks outer rim hasradius R = 4.20 m, and F1 = 10.5 N. Find the magnitude ofeach torque exerted around the center of the disk. FIGURE P12.71 Problems 71-75arrow_forwardIn Figure P10.40, the hanging object has a mass of m1 = 0.420 kg; the sliding block has a mass of m2 = 0.850 kg; and the pulley is a hollow cylinder with a mass of M = 0.350 kg, an inner radius of R1 = 0.020 0 m, and an outer radius of R2 = 0.030 0 m. Assume the mass of the spokes is negligible. The coefficient of kinetic friction between the block and the horizontal surface is k = 0.250. The pulley turns without friction on its axle. The light cord does not stretch and does not slip on the pulley. The block has a velocity of vi = 0.820 m/s toward the pulley when it passes a reference point on the table. (a) Use energy methods to predict its speed after it has moved to a second point, 0.700 m away. (b) Find the angular speed of the pulley at the same moment. Figure P10.40arrow_forward
- A stepladder of negligible weight is constructed as shown in Figure P10.73, with AC = BC = = 4.00 m. A painter of mass m = 70.0 kg stands on the ladder d = 3.00 m from the bottom. Assuming the floor is frictionless, find (a) the tension in the horizontal bar DE connecting the two halves of the ladder, (b) the normal forces at A and B, and (c) the components of the reaction force at the single hinge C that the left half of the ladder exerts on the right half. Suggestion: Treat the ladder as a single object, but also treat each half of the ladder separately.arrow_forwardA bridge of length 50.0 m and mass 8.00 104 kg is supported on a smooth pier at each end as shown in Figure P12.25. A truck of mass 3.00 104 kg is located 15.0 m from one end. What are the forces on the bridge at the points of support? Figure P12.25arrow_forwardFind the net torque on the wheel in Figure P10.23 about the axle through O, taking a = 10.0 cm and b = 25.0 cm. Figure P10.23arrow_forward
- Scientists have studied how snakes grip and climb ropes. In one study, they found that an important characteristic of a rope is its "compliance"--that is, how easily the rope, while under tension, can be flexed. (Figure 1) shows how scientists measured a rope's compliance by attaching it to two strings, each supporting an identical mass m. The lower part of the rope is held under tension by a spring (not shown). The strings contort the rope so that its middle section lies at angle θ. . a)For θ = 45 ∘ and m = 300 g, what is the tension T1 in the upper part of the rope? For θ = 45 ∘ and m = 300 g, what is the tension T2 in the middle part of the rope?)arrow_forwardScientists have studied how snakes grip and climb ropes. In one study, they found that an important characteristic of a rope is its "compliance"--that is, how easily the rope, while under tension, can be flexed. (Figure 1) shows how scientists measured a rope's compliance by attaching it to two strings, each supporting an identical mass mm. The lower part of the rope is held under tension by a spring (not shown). The strings contort the rope so that its middle section lies at angle θ. For θ = 45∘ and mm = 400 g, what is the tension T2 in the middle part of the rope?arrow_forwardWhat is the simplest way to solve this question because I am struggling with it.arrow_forward
- Principles of Physics: A Calculus-Based TextPhysicsISBN:9781133104261Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningGlencoe Physics: Principles and Problems, Student...PhysicsISBN:9780078807213Author:Paul W. ZitzewitzPublisher:Glencoe/McGraw-HillPhysics for Scientists and Engineers: Foundations...PhysicsISBN:9781133939146Author:Katz, Debora M.Publisher:Cengage Learning
- Physics for Scientists and Engineers with Modern ...PhysicsISBN:9781337553292Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningPhysics for Scientists and EngineersPhysicsISBN:9781337553278Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningCollege PhysicsPhysicsISBN:9781305952300Author:Raymond A. Serway, Chris VuillePublisher:Cengage Learning