Introduction Company T is engaged in the manufacturing of toys and board games. The firm is known for its innovations and quality products. The company sales had declined during the past six months. Person ME, who is the production manager , attributed the economy for the decline in sales. He undertook some measures like cutting down production costs, and laying employees off in the design and product development departments, but all the efforts did not contribute to the growth in the profit. The vice president of sales has been concerned with the customer complaints. Person KM, the assistant of the vice president, suggested making a trade-off for the defective products by getting back the defective items from the customer and providing a new one, which would please the dissatisfied customer. The defective items can be repaired and could be sold at adiscounted price. Person SB, the production assistant, suggested to increase the level of inspection. With 100% level of inspection the number of defectives could be reduced. To determine : The recommendations to the company as a consultant.

Question

Want to see the full answer?

Answer 1

Question

Chapter 10, Problem 1.1CQ

Summary Introduction

Introduction

Company T is engaged in the manufacturing of toys and board games. The firm is known for its innovations and quality products. The company sales had declined during the past six months. Person ME, who is the production manager, attributed the economy for the decline in sales. He undertook some measures like cutting down production costs, and laying employees off in the design and product development departments, but all the efforts did not contribute to the growth in the profit.

The vice president of sales has been concerned with the customer complaints. Person KM, the assistant of the vice president, suggested making a trade-off for the defective products by getting back the defective items from the customer and providing a new one, which would please the dissatisfied customer. The defective items can be repaired and could be sold at adiscounted price.

Person SB, the production assistant, suggested to increase the level of inspection. With 100% level of inspection the number of defectives could be reduced.

To determine: The recommendations to the company as a consultant.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Students have asked these similar questions

What the different between a near miss and hazard 1. movement and contact 2. Contact 3. movement

The fixed and variable costs for three potential manufacturing plant sites for a rattan chair weaver are shown: Site Fixed Cost Per Year Variable Cost per Unit 1 $700 $12.00 2 $1,000 $7.00 $2,200 $5.00 a) After rounding to the nearest whole number, site 1 is best below After rounding to the nearest whole number, site 2 is best between After rounding to the nearest whole number, site 3 is best above b) If the demand is 590 units, then the best location for the potent 3 units. and units. 600 0 60 units. g plant is

Refer to Table S6.1 - Factors for Computing Control Chart Limits (3 sigma) for this problem. Sampling 4 pieces of precision-cut wire (to be used in computer assembly) every hour for the past 24 hours has produced the following results: Hour R Hour X R Hour X R Hour X R 1 3.25" 0.71" 7 3.15" 0.58" 13 3.11" 0.85" 19 4.51" 1.56" 2 3.20 1.18 8 2.65 1.08 14 2.83 1.31 20 2.79 1.14 3 3.12 1.38 9 15 4. 3.39 1.31 10 5 2.97 1.17 6 2.76 0.32 3.02 0.71 3.12 1.01 2.75 1.33 16 2.74 0.50 22 11 2.73 1.17 17 2.76 1.43 23 12 2.87 0.45 18 2.64 1.24 21 2.75 1.03 3.18 0.46 2.94 1.53 24 2.54 0.97 Based on the sampling done, the control limits for 3-sigma x chart are (round all intermediate calculations to three decimal places before proceeding with further calculations): Upper Control Limit (UCL) = inches (round your response to three decimal places). Lower Control Limit (LCL) = inches (round your response to three decimal places). Based on the x-chart, the wire cutting process has been The control limits…