You are requested to use SIMATIC S7-300 PLC to control the following operations on the mini-mechatronics kit. Make all required connections between PLC I/O ports and I/O terminal rail. Write a Step 7 program to control the following operations: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Place two parts in the feeding magazine (metallic and nonmetallic) Press a Toggle start/stop (ON/OFF) switch to initiate the system. System works only if Toggle is ON. The ejector plate of the supply unit should push one part onto the conveyor. The conveyor turns on and transfers the part past the sensor unit, where it is checked for material type, to the stopper unit. When the part is checked, the spindle rotates moving the 3-position holding platform from its position (1st or 2nd) to the desired position (2nd or 1st), if needed: a. 1st position for Metal. b. 2nd position for the Plastic In other words, if the checked part is metallic and the platform in 2nd position, the spindle moves, if it was in the 1st position, the platform stays in place. Note that we will be using only 2 positions from the 3-position platform. When the part reaches the stopper, the z-axis cylinder goes down, the suction pad picks the part up, and then z-axis retracts. The x-axis cylinder extends to drop the part in place, while it is in the z-axis upper position. The x-axis retracts to initial position. The process repeats. Use the counters to count the different types of workpieces processed through the system.
You are requested to use SIMATIC S7-300 PLC to control the following operations on the mini-mechatronics kit. Make all required connections between PLC I/O ports and I/O terminal rail. Write a Step 7 program to control the following operations: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Place two parts in the feeding magazine (metallic and nonmetallic) Press a Toggle start/stop (ON/OFF) switch to initiate the system. System works only if Toggle is ON. The ejector plate of the supply unit should push one part onto the conveyor. The conveyor turns on and transfers the part past the sensor unit, where it is checked for material type, to the stopper unit. When the part is checked, the spindle rotates moving the 3-position holding platform from its position (1st or 2nd) to the desired position (2nd or 1st), if needed: a. 1st position for Metal. b. 2nd position for the Plastic In other words, if the checked part is metallic and the platform in 2nd position, the spindle moves, if it was in the 1st position, the platform stays in place. Note that we will be using only 2 positions from the 3-position platform. When the part reaches the stopper, the z-axis cylinder goes down, the suction pad picks the part up, and then z-axis retracts. The x-axis cylinder extends to drop the part in place, while it is in the z-axis upper position. The x-axis retracts to initial position. The process repeats. Use the counters to count the different types of workpieces processed through the system.
Elements Of Electromagnetics
7th Edition
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Sadiku, Matthew N. O.
ChapterMA: Math Assessment
Section: Chapter Questions
Problem 1.1MA
Related questions
Question
I need PLC diagram on PLC software or by hand.
Transcribed Image Text:Experimental Procedure:
You are requested to use SIMATIC S7-300 PLC to control the following operations on the
mini-mechatronics kit. Make all required connections between PLC I/O ports and I/O terminal
rail.
Write a Step 7 program to control the following operations:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
Place two parts in the feeding magazine (metallic and nonmetallic)
Press a Toggle start/stop (ON/OFF) switch to initiate the system. System works only if
Toggle is ON.
The ejector plate of the supply unit should push one part onto the conveyor.
The conveyor turns on and transfers the part past the sensor unit, where it is checked
for material type, to the stopper unit.
When the part is checked, the spindle rotates moving the 3-position holding platform
from its position (1st or 2nd) to the desired position (2nd or 1st), if needed:
a. 1st position for Metal.
b. 2nd position for the Plastic
In othe words, if the hecked part is
and the platform in 2nd position, the
spindle moves, if it was in the 1st position, the platform stays in place. Note that we
will be using only 2 positions from the 3-position platform.
When the part reaches the stopper, the z-axis cylinder goes down, the suction pad
picks the part up, and then z-axis retracts.
The x-axis cylinder extends to drop the part in place, while it is in the z-axis upper
position.
The x-axis retracts to initial position.
The process repeats.
Use the counters to count the different types of workpieces processed through the
system.
Expert Solution
This question has been solved!
Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.
Step by step
Solved in 2 steps with 1 images
Recommended textbooks for you
Elements Of Electromagnetics
Mechanical Engineering
ISBN:
9780190698614
Author:
Sadiku, Matthew N. O.
Publisher:
Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:
9780134319650
Author:
Russell C. Hibbeler
Publisher:
PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:
9781259822674
Author:
Yunus A. Cengel Dr., Michael A. Boles
Publisher:
McGraw-Hill Education
Elements Of Electromagnetics
Mechanical Engineering
ISBN:
9780190698614
Author:
Sadiku, Matthew N. O.
Publisher:
Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:
9780134319650
Author:
Russell C. Hibbeler
Publisher:
PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:
9781259822674
Author:
Yunus A. Cengel Dr., Michael A. Boles
Publisher:
McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:
9781118170519
Author:
Norman S. Nise
Publisher:
WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:
9781337093347
Author:
Barry J. Goodno, James M. Gere
Publisher:
Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:
9781118807330
Author:
James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:
WILEY