ushbutton swi ting piston rod ressed again t

Q: It asks what is the width across the flats of the locking bolt head?

A: The width across the flats of the locking bolt head is 0.5625

Q: Why must a cylinder ridge be removed before attempting to remove the piston?

A: Cylinder ridge reamer is a component use to remove the ridge.

Q: I need the answer for problem number 14.

A: 14.In this drawing, only one chamfer is represented by the leader line. The chamfer is represented…

Q: This part of the a cylinder holds the piston in place and helps support the rod as it extends. a.…

A: Option c is correct.

Q: Can I get some help looking over some sheets? I have most filled out, but just to double check for…

A: During four stroke the crankshaft turns twice — moving each piston up and down twice — while the…

Q: the rim and face alighnment method is a.used only to alighn solid flange couplings b.less accurate…

A: Rim and face method is also called the dial indicator method. it consists of the installment of two…

Q: Technician A says all gaskets should be discarded during teardown to keep the work area clean.…

A: Gasket : A gasket is a mechanical seal i.e it is used to close up the gap between two mating…

Q: How do you read the tolerance for the bolt?

A: Given :-  Bolt drawing   Find :-  How do u read the tolerance of the bolt = ?

Q: Do not use _____ on nuts and bolts unless someone has rounded off edges of the nut or bolt.

A: Solution:

Q: Hello, I have some diagrams I have filled out for practice that I would like to use to study for an…

A: Diagram 1. E - relief valve A- gear pump D- rotor F- internal gear C- internal and external gear…

Q: Tech a says that the push on the piston top during the power stroke is transferred to the crank…

A: Tech a is correct.

Q: What material is the piston? None of these answers are correct Steel Cast iron O Aluminum

A: Given:   To select the correct option for the material of the piston.

Q: Task 5 - Brake Callipers and Discs Brake callipers and discs, like the braking system are different…

A: given; (1) examine the example caliper  and examine the material used? (2) How many piston are used…

Q: Worn teeth on a speed gear can cause?

A: worn teeth creates a big problem in gear drive.

Q: to provide a good sealing joint between the cylinder head and exhaust, apply a sealant to the…

A: Question:- To provide a good sealing joint between the cylinder head and exhaust, apply a sealant to…

Q: When removing the balance shaft assembly: tech a inspects the bearings for unusual wear or damage.…

A: Balance shafts are serviced in the same way as crankshafts.there are two main causes of removing or…

Q: How is the air exhausted at the back of the piston when the piston retracts?

A: By employing a single acting air cylinder in the application rather than a more traditional…

Q: Which of the following ensures proper timing of the intake and exhaust valve events?

A: The timing of the intake and exhaust valve events helps in proper timely working of the engine.

Q: Damaged swaged-end fittings on a piece of flexible hydraulic hose ___________________ (can or…

A: Damaged swaged-end fittings on a piece of flexible hydraulic hose cannot  be replaced.

Q: Match the symbol to the component: а. Pump b. Motor c. Cylinder with retract cushion d. Pressure…

A:

Q: Need help drawing a 1/2-13 UNC 2A Hex head bolt

A: THIS HOW IT'S GONNA BE

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.