Based on pneumatic components given in Figure 1, construct one cascade circuit using two air-line concept to move double acting cylinders A and B with process sequence A+B+B−A−  .

Q: Inc.f H Dec.th Unit 1 Supply P Control lever Tho Feedback lever Float tho Ho

A: In a liquid-level control system, a float, attached to a control lever, is often used as a sensor.…

Q: Design a digital lag compensator for the position control system below to meet the following…

A: To determine: Design a digital lag compensator.

Q: (15) Consider the following inverted pendulum problem. Segway Balancing a stick Inverted pendulum…

A: Given : To find : Block diagram

Q: 1- For the system shown in Figure 2 a) Find system response when r(t) = 0 and 2(t) is unit step b)…

A: this question about the moment of inertia of the shaded region about the centroidal x and y axes.…

Q: a)If the system has a transfer function of the form G_P (s)=H(s)/(V_m (s) )=μ/(1+Ts) where µ is the…

A: Please refer below pages and if you have any doubt please feel free to ask meExplanation:Step 1:Step…

Q: 1. For the system shown below, Forearm w(1) Schematic of a motor driver in an arm prosthesis.…

A: Given: J=0.1kg-m2B=0.2N-m/rad/sec To find the transfer function of the system,

Q: Determine the output speed and the direction of rotation when the input speed is 3000 rpm (Figure.…

A: The input speed =3000rpmLink 3 does not have a fixed axis of rotation.Link 2 is connected to Link 3…

Q: For the control system shown in fig-2, a) Find the values of K and K₁, such that the closed loop…

A: Given:To find:

Q: For the motor, load, and torque-speed curve shown, find the transfer function G(s) = 0,(s)/E(s). Ru…

A:

Q: 2. Consider the spring-mass-damper system shown in Figure 1. Ifm = 10 kg, b=30 N-s/m, k = 1000 N/m,…

A: For solution refer below images.

Q: For the system shown a step torque is applied at 0₁(t). Given J and k1Nm. Find: = rad 1. The…

A:

Q: 4.-Determine if the system that has the input-output ratio: Y(c) = x(sen(t)). No use chatgpt

A: Step 1:Step 2:

Q: Q.7 (b) For the heat exchanger shown in Figure.6, draw the schematic diagram for a combined…

A: The feedforward controller is one which can improve the reliability of feedback controller and this…

Q: Q.5- Consider the liquid-level control system shown in Figure below. assume that the velocity of the…

A: Given:To find:Determine the transfer function.

Q: Dynamics of a current controller DC motor is given as follows: KimJm+bB where, ẞ denotes the shaft…

A: % ParametersJm = 0.48;  % kg*m^2bm = 0.2;   % Nms/radKt = 0.96;  % Nm/A% Transfer function of the…

Q: Consider the following mathematical model of a single-link flexible joint robotic manipulator (shown…

A:

Q: The Rexroth simulators have the following component specifications: Double acting cylinders with…

A: Given : Dp = 25 mm = 2.5 cm Dr = 16 mm = 1.6 cm Q = 8 L/min = 133.33 cm3/s To find : Theoretical rod…

Q: Q.5- Consider the liquid-level control system shown in Figure below. assume that the velocity of the…

A: To find:Determine the transfer function.

Q: Design a synchronous sequential logic circuit that counts through the repetitive binary sequence…

A: Step 1:Step 2:

Q: feedback-- the --- -- -- difference between the setpoint and measured position so the feedback can…

A: Positive feedback are sometimes unstable, positive feedback can result in violent and sustained…

Automation in manufacturing processes

The term automation refers to the technique through which the creation of an apparatus takes place using an automatic process or a system. Let us try to understand this with an example.