Q.7 (b) For the heat exchanger shown in Figure.6, draw the schematicdiagram for a combined feedforward-feedback controller in which inlet feedtemperature in the major load variable, and outlet temperature is thecontrolled variable. The combined controller output is the set point for thesteam pressure controller.SteamFeedCondensateFigure.6

The feedforward controller is one which can improve the reliability of feedback controller and this…

Answered: Q.7 (b) For the heat exchanger shown in…

Q.7 (b) For the heat exchanger shown in Figure.6, draw the schematic diagram for a combined feedforward-feedback controller in which inlet feed 6

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The satallite system below is controlled using reaction wheels. The torque wheel input for the system is u(s) and the satallite attitude is Ө(s) For a strong communication link Ө needs to be a value where the satallite atenna is pointing at the ground station The transfer function for this system will be shown in the picture. Design a feedback control system that sets the closed loop damping ratio at 0.8 and the natural frequency is at 10 rad/sec.
b) Consider the evaporator which concentrated the salt solution and the transfer functions of all open systems are first-order system. 1) Design the cascade control loop and block diagram. If the evaporator temperature and steam flowrate of coil are controllerd variables and if the inlet concentration and presure of coil steam are disurbance variables.
3 6 4 2 Imaginary Axis -10 -8 -6 -4 -2 0 Real Axis
Problem 1. controller, and G(s) = Consider the control system shown in Fig. 1, where De(s) is the 1 (s - 1)(s+5) 1) (5 points) Is the open-loop system stable? 2) (15 points) Assume that De(s) = K. Rewrite the closed-loop characteristic equation in the root-locus form 1 + KL(s) = 0. Sketch the root locus for L(s). Is it possible to stabilize the system using a proportional controller? == 3) (10 points) Assume that a PD-controller is used to control the system, i.e., De(s) KpKDs. Utilize the Routh-Hurwitz criterion to derive stability conditions for the closed-loop system. + Ro Σ Dc(s) G(s) -OY Figure 1: Control system in Problem 1.
If the system is to be arranged in a closed-loop, with a controller gain K in the forward path and a unity negative feedback loop, what is the maximum value of K which could be used without the system becoming unstable? Assuming you use Figure Q5 for this, use a sketch to show how you obtained the values from the plot.
A plant of transfer function G(s) is to be operated in closed-loop, with unity negative feedback, and a controller in the forward path as shown in Figure Q4 (a) R +1 E U Y controller G(s) Figure Q4 Discuss the main steps of generating the root-locus plot for the closed-loop system of Figure Q4
Consider unity negative feedback system shown below: a) G₁ (s) = = R(s) b) G₂ (s) = Sketch and refine the root locus. Discuss and calculate the number of branches, the real axis segments, the starting and ending points, asymptotes, breakaway and break-in points, and jw axis crossings, if any. K(s+3) (s+2)(s+5)(s+6)' E(s) K(s+1)(s+3) (s²-2s+4) G(s) C(s)
Break gap | k mp Vp F 17 Sp Kp ww Xp Xb Xp(s) F(s) Determine the transfer function for if the break gap is greater than zero. Кр M Cb Vs Slider pin: Applies friction to System as the break Gap is greater than Zero
A. The open-loop transfer function of a unit negative feedback control system is as K GK (S)=- (s+ 1)(s + 2)(s+3)(s+4) (1) Evaluate the value range of K when the closed-loop system is stable; (2) Calculate the steady-state error of the system when the input is the unit step signal.
Please don't provide handwritten solution ....
Given the system equipped with unitary feedback, whose direct branch transfer function is: Design a PID controller with one of the Ziegler-Nichols methods.
The open loop transfer function of a unity feedback control system is given below; G(s) = K s(s+2)(s2+2s+2) Plot the root locus and determine the value of k at the break away point.