3. Sketch a house's heating system which containing a gas furnace that heats water which circulates to radiators on the walls, and a thermometer that is connected to a control module that can turn the furnace on or off. The outside temperate is Text, the inside temperature is T, and the desired temperature is Ta. Describe the elements of the feedback control loop.

3. Sketch a house's heating system which containing a gas furnace that heats water which circulates to radiators on the walls, and a thermometer that is connected to a control module that can turn the furnace on or off. The outside temperate is Text, the inside temperature is T, and the desired temperature is Ta. Describe the elements of the feedback control loop.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Problem 1. controller, and G(s) = Consider the control system shown in Fig. 1, where De(s) is the 1 (s - 1)(s+5) 1) (5 points) Is the open-loop system stable? 2) (15 points) Assume that De(s) = K. Rewrite the closed-loop characteristic equation in the root-locus form 1 + KL(s) = 0. Sketch the root locus for L(s). Is it possible to stabilize the system using a proportional controller? == 3) (10 points) Assume that a PD-controller is used to control the system, i.e., De(s) KpKDs. Utilize the Routh-Hurwitz criterion to derive stability conditions for the closed-loop system. + Ro Σ Dc(s) G(s) -OY Figure 1: Control system in Problem 1.
1. Give an example of open loop and closed loop system (one example each). Also state the input, control system, feedback and output parameter. Example. 1. Open Loop - Water Heater: Input - Water Temperature (Cold) System - Heating Element Output - Water Temperature (Hot) 2. Closed Loop - Air-conditioning System Input - Desired Room Temperature Control - Motor controller/Compressor/ACU Feedback - Temperature Sensing Output - Room Temperature
answer with complete solution
QUESTION 3 An open loop transfer function with a unitary feedback control system is given K by G(s) =- where K is the gain of the system. An open loop (s+1)(s+4) transfer function with a PID controller must be designed in order to yield a peak time of 1.047 s, and a damping ratio of 0.8. 3.1. Calculate the design point s, of the system 3.2. Calculate the gain and the zero(s) of the PID controller 3.3. Provide the block diagram of the compensated system with the PID controller
If the system is to be arranged in a closed-loop, with a controller gain K in the forward path and a unity negative feedback loop, what is the maximum value of K which could be used without the system becoming unstable? Assuming you use Figure Q5 for this, use a sketch to show how you obtained the values from the plot.
control of mechanical system give me correct option
For a unity negative feedback control system having an open-loop transfer function, G(s) as given below. Find out the value of "K" such that the system will be in the stable region. (K/s) (s3 + 12. 5s2 + 50. 5s + 66) G(s) =
Give a physical example for feedback control systems. Sketch the block diagram with input and output variables: Missile launch system
Below is an open loop transfer function which is given: A(s) A(s) = = 0.1(s +14) (s+7)(s + 5) Use matlab's bode function and plot its bode diagram. Show the figure Use the following MATLAB script and write a code for bode plotting concerning the open loop transfer function. Clear Close all clc w 0. 1:0.001:100; ns = length (w); for i=1:nS %Write the code here end
Hand written plzzz...i'll give you multiple upvote..asap...
Please give some idea.
(Figure 1 One Wheel Model), Part1-(Derive equation of motion for a given system and obtain transfer function and state space representation.) , part2-(Draw closed-loop diagram for full-state- feedback controller.) , part3- (Select proper coefficient (u=-Kx) satisfying that .) part4- (Simulate the closed-loop system and show the response of it.) Note: Tahe Reference signal as With f = 0.1 Hz. !!!!!!!!! Please solve these steps, at least the first step which is writing the equations of motion of the system and the second step which is drawing closed loop diagram for Full state feedback controller.!!!!