Xenon and fluorine were mixed in a 1:1 ratio by volume and sealed in a vessel attached to a barometer. After some time, crystals were found to have formed on the walls of the vessel and the barometer showed that the pressure had dropped to 70% of its original pressure. Analysis of the gases remaining indicated 4 parts xenon to 3 parts fluorine. Assuming that the temperature remained constant and only one crystal product was formed, construct a balanced equation with state symbols for the reaction.

Xenon and fluorine were mixed in a 1:1 ratio by volume and sealed in a vessel attached to a barometer. After some time, crystals were found to have formed on the walls of the vessel and the barometer showed that the pressure had dropped to 70% of its original pressure. Analysis of the gases remaining indicated 4 parts xenon to 3 parts fluorine. Assuming that the temperature remained constant and only one crystal product was formed, construct a balanced equation with state symbols for the reaction.

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

please help solve Concentration of AR Stock Solution (ppmppm) 21.22 Unrounded Rounded Concentration of AR Stock Solution (μMμM) 42.7461 42.7
SELECT correct responses only 1) Volume percent (v/v%) is temperature-independent. 2) There are three major approaches to expressing solution concentration in terms of percent concentration: weight percent, volume percent, and weight/volume percent. 3) Weight/volume percent (w/v%) is a unit-less quantity. 4) The term 'percent' refers to 'parts per thousand'. 5)A standard solution is a reagent of known concentration that is used to carry out a volumetric titration. 6) The endpoint of a titration is the theoretical point reached when the amount of added titrant is chemically equivalent to the amount of analyte in a sample. 7) A substance that changes color in response to chemical equivalence is known as an indicator. 8) Given a sufficiently diligent and experienced experimenter, it is sometimes possible to reach a titration volume error value of 0.
A standard curve was produced using varying concentrations of KCl and the results are shown below. A sample of pond water was found to have a conductivity of 535 µS/cm. What is the concentration of total dissolved solids in the water sample? Recall the TDS constant is 0.67. CONDUCTIVITY (MICROS 1600 1400 1200 1000 800 600 200 0 Standard Curve of Conductivity vs Concentration Concentrations (M) 0.002 A. 392 mg/L B. 478 mg/L ✓C. 798 mg/L D. 247 mg/L 0.004 y = 132208x + 19.045 R²-0.9996 0.006 CONCENTRATION (M) 0.008 0.01 0.012
Question 4 What is the approximate boiling point of the liquid in the mixture with a lower boiling point? Sample Distillation Data 120 100 80 60 40 20 0 0 0.5 00 1 ● 1.5 2 2.5 3 3.5 ● ● 4 4.5
Sel Absorbance S Verify your molar absorptivity value. Did you report your data to the correct number of significant figures? Analytical wavelength Analytical wavelength for blue dye (nm) Calibration curve Solution 1 2 3 4 5 Dye concentration (μM) 15.20 7.51 Unknown solution 3.74 1.89 1.01 Molar absorptivity (μM ¹cm-¹) Absorbance Concentration of unknown blue dye (µM) 629 Absorbance 0.756 0.432 0.259 0.175 0.144 0.083 How to calculate concentration from absorbance S A d tra 01
LabQuest 17 DATA TABLE Trial 1 2 3 4 5 6 Concentration (mol/L) 0.080 0.16 0.24 0.32 0.40 Unknown number Absorbance (no units) 0.2711 0.437 1.480 1.932 2.171 0.3 DATA ANALYSIS 1. Describe an alternate method for determining the molar concentration of your unknown sample of copper (II) sulfate solution, using the standard data.
Chemistry Which lab technique(s) can be performed on solid, somewhat soluble samples? Melting Range Determination or Recrystallization. Melting Range Determination. Not Recrystallization. Neither Recrystallization nor Melting Range Determination. Recrystallization. Not Melting Range Determination.
You have 100 mL of solvent available to do an extraction. Which will give a better separation?a. 1 extraction with 100 mLb. 2 extractions with 50 mLc. 5 extractions with 20 mLd. 3 extractions with 25 mL
Data Analysis: 1. Create an Absorbance (Y) vs. Concentration (X) graph using data from the six standard solutions above. 2. Perform a linear trendline analysis of your six data points. Display the equation and R² value on the graph with a minimum of 8 decimal places. 3. On the same graph, perform a 2nd order polynomial trendline analysis of your six data points. Display the equation and R² value on the graph with a minimum of 8 decimal places. 4. Turn in your graph as the last page of this report. 5. On a separate piece of paper calculate the concentration of the unknown solution using both the linear and 2nd order polynomial trendline equations (Show all work) 6. Choose the best unknown concentration from #4 above and report it with three significant figures in the unknown data table above.
Standardization of 0.10 M HCl1. Take three (3) clean and properly labeled 250-mL Erlenmeyer flasks. Into the three flasks, weigh 0.1 g of the primary standard Na2CO3 to the nearest 0.1 mg. Record the weights of the primary standard.2. Add about 75.0 mL of boiled distilled water and swirl to dissolve the solids.3. Add 2 to 3 drops of phenolphthalein indicator. Record the initial burette reading and titrate with the prepared 0.10 M HCl solution until phenolphthalein endpoint.4. Record the final burette reading for each titration in your data sheetDetermination of Ksp and Molar Solubility1. Add Ca(OH)2 to 250.0 mL distilled water with stirring until equilibrium is achieved. 2. Filter the undissolved precipitate. Measure out 50.0 mL of the supernate into a 250-mL Erlenmeyer flask using a pipette.3. Add a few drops of phenolphthalein indicator and titrate with standardized HCl solution until endpoint is achieved.4. Record the volume the HCl solution used. Perform two more trials.…
Find the weight percent %Ca
1. You begin by measuring 10.00 mg of dye on a precise analytical balance and dissolve the dye in 1.000 1 of water having density 998.25 kg/m³. What is the concentration of the dye in mg/l, kg/m³, mg/kg, and ppm?