Write an assembly language program to generate a square wave with a delay of 7 ms (ON time) when intl is activated and generate a square wave with a delay of 5 ms (ON time) delay when int0 is activated.Assume XTAL as 11.0592 MHz,use timero in model. Elucidate the calculation involved in the program

Write an assembly language program to generate a square wave with a delay of 7 ms (ON time) when intl is activated and generate a square wave with a delay of 5 ms (ON time) delay when int0 is activated.Assume XTAL as 11.0592 MHz,use timero in model. Elucidate the calculation involved in the program

Computer Networking: A Top-Down Approach (7th Edition)

7th Edition

ISBN:9780133594140

Author:James Kurose, Keith Ross

Publisher:James Kurose, Keith Ross

Chapter1: Computer Networks And The Internet

Section: Chapter Questions

Problem R1RQ: What is the difference between a host and an end system? List several different types of end...

See similar textbooks

Similar questions

Assume we are writing a testbench for a sequential circuit that has three control inputs (cA, cB, cC) and a periodic clock (clk). If we define CLK_PERIOD as a localparameter with a value of 50 (nsec), write the testbench segment that would ensure all possible combinations of the control inputs were tested on a clock rising edge. This is can be done more elegantly if you define each time step in terms of the constant CLK_PERIOD. Your answer should include the statements that define clk, cA, cB, and cC over time. Hint: think of how you would show all combinations of three variables on a truth table and replicate that over time, where each combination is held over a timespan with a clock triggering edge.
Using Logism Softwarel The most important and possible most difficult component to implement is the 8 bit arithmetic logic unit. Thefunctions of the ALU are shown in Table 1. The ALU should have 5 inputs (A-input, B-input, F0-input, F1-input, Finput) and 1 output (C-output). You will need to determine how many bits each input and output should have.Remember, you are designing an 8-bit microprocessor! . For example, to add the value on the A-bus8-bit ALUto the value on the B-bus, you can simply use an 8-bit adder. Explore the components in Logisim! Additionally,you can think about using a multiplexer to determine which ALU function will be performed
QUESTION 5 35 A convolutional circuit has three internal registers (s0, s1, and s2), and two outputs (c0 and c1), calculated as follows: c0=i+s2; c1=i+s0+s1. We are currently in state 110 and receive input 0. What is the output and next state? O c0=0; c1=0; next=011 O c0=1; c1=0; next=011 O c0=1; c1=1; next=011 O c0=0; c1=1; next=011 QUESTION 6 11 A convolutional circuit has three internal registers (S0, S1, and s2), and two outputs (c0 and c1), calculated as follows: c0=i+s0; c1=i+s1+s2. We are currently in state 110 and receive input 0. What is the output and next state? O c0=1; c1=1; next=011 O c0=0; c1=1; next=011 O c0=0; c1=0; next=011 O c0=1; c1=0; next=011 QUESTION 7 02 A convolutional circuit has three internal registers (s0, s1, and s2), and two outputs (c0 and c1), calculated as follows: c0=i+s0; c1=i+s0+s1. We are currently in state 011 and receive input 1. What is the output and next state? O c0=0; c1=1; next=101 O c0=0; c1=0; next=101 O c0=1; c1=0; next=101 O c0=1; c1=1;…
Assume that an external clock signal is being fed into pin T0CKI (RA4). Write a C program touse Timer0 in 8-bit mode to count the pulses and display the state of the TMR0L count onPORTB. Start the count at 0x00 and stop the count at 0xFF+1. Use the MPLAB simulatorto verify the proper operation of the program
CLK Do C lo 20 D₁ C 2₁ 2₁ D₂ C 2₂ Figure 1 . Using the asynchronous ripple counter in Figure 1 and assuming that the propagation delay from an input clock to a change in the output of Q is 9ns, what is the worst-case delay (i.e. longest delay) between an input clock pulse and the counter being in a final state. Give which state(s) of the counter have the worst-case delay.
Realize a Moore machine with one external input S and a 3-bit output 020100 representing a 3-bit binary number. The circuit outputs indefinitely either the sequence of values 1, 3, 5, 1, 3, 5, 1, 3, ... when S=1, or the sequence of values 1, 5, 3, 1, 5, 3, 1, 5, ... when S=0. Use a binary state encoding with exactly 2 D flip-flops. You can decide when transitions between the sequences occur, the new sequence can start at any digit. On reset the system starts by showing the number 3. i) write the state diagram; include the transition conditions and the output value; ii) write the truth table for the next state; iii) write the truth table for the output;
Implement Lamport’s logical clocks with three process p1, p2, p3 where each clock duration at 3, 5, and 6 respectively
In a synchronous finite state machine, when does a transition between states occur?
Write an assembler program that produces a square wave at 50% duty cycle rate without using a timerand outputs this signal from the P1.0 terminal. (To be done with the delay program)
I asked the question before and the answer I got does not makes sense. My question is why did not we considered the Adder, Shift, ANd, Control when calculation delay time.? Again, it is in Risc-V.
Solve number 2
Suppose some hypothetical system’s control unit has a ring (cycle) counter consisting of some number of D flip-flops. This system runs at 1GHz and has a maximum of 10 microoperations/instruction. Q. What is the maximum frequency of the output (number of signal pulses) output by each flip-flop?