What station is responsible for daily management and control of the satellites and the control segment? a. Control Segment b. Space Segment С. User control center d. Master control center CLEAR MY CHOICE

Q: Please explain, in our own words, the difference between the "d operator" and the "8 operator."

A: Both operators are used to represent change in some quantity.

Q: throttle actuator velocity v intake pipe throttle angle (aTH) slope (a) For vehicle speed control…

A: given; ⇒moving velocity =v⇒car moving with acceleration =a  ⇒lets take weight of body =w⇒normal…

Q: Which of the following is correct for a open loop system ?

A: The main problem with the open loop control system is that, it do not monitor or check the condition…

Q: 8. Dynamics of tank with outflow centrifugal pump 8.1. Identify the plant dynamics (tank) with…

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: Considerations : End Effector weight: 1KG L3 Object weight : 4.2 KG M3 = M2 = 3.8KG [Motor M 3…

A: Robot              Note :- you have posted multiple questions on single window. As per the…

Q: In which control system, output from the system has no effect on command signal? O a. Feedback less…

A: In Feedback less system, output from the system does not sent back to the controller. Therefore,…

Q: A 5-m hollow steel shaft (G= 80 GPa) is subjected to a 25 kN-m torque. The outer diameter is 200 mm.…

A: Given data:- Length of shaft =5-m G=80 GPa Torque (T)=25 kN-m The outer diameter (D) = 200 mm. The…

Q: For Industrial Maintence What is defined in Section VIII of an MSDS?

A: What is defined in Section VIII of an MSDS?

Q: ushbutton swi ting piston rod ressed again t

A:

Q: i. A Wind Generator with the following data is installed at a wind site. Power output from the…

A:

Q: is an interconnection of components forming a system configuration that will provide a desired…

A:

Q: In the mid-1900s, several technological and analysis concepts came together to make the PID…

A: A PID controller regulates temperature, flow, pressure, speed, and other process variables in…

Q: The worktable of a numerical control machine tool is driven by a closed-loop positioning system…

A: Given data as below:pitch p = 0.25 in/revthe distance at which table moved x = 7.5 infeed rate fr =…

Q: Modifying of a measured signal to a desired form, including the amplifying of it, happens at A.…

A: To choose. The correct option. Concept used: Signal-conditioning: Signal conditioning is the…

Q: what is the 95% horizontal positioning error in an

A: Positional accuaracy = C = 0.1

Q: For the following automatic control systems commonly encountered in daily life, identify the devices…

A: Given: Automatic sprinkler system for fires  Automobile cruise speed control  Refrigerator…

Q: Which is the final element of a measurement system ? a. Sensing Element b. Signal Transmission…

A: The Basic elements of any measuring system are the primary sensing element, signal processing…

Q: Zo To L BASE Yo Xo Y₂ Уз У4 04 ZA TOOL d3 Tutorial Question 5 Let d₁=2, a₁=1, a₂=1, d3=1.5, d₁=0.5,…

A: \The values are .The x coordinate of end effector in its own frame of refrence is The coordinates of…

Q: No software is required. I just need a explaintion of what is happening to this truss.

A: The figure shows the translation or the movement of the truss with respect to its original position.…

Q: ____is a type of control system in which the process output is controlled at the setpoint level. a.…

A: Process controls are a type of linear feedback control system in which the controlled variable is…

Q: Sketch an automatic control system diagram for: 1. Hydraulic Control System 2. Electric Control…

A: Given Control System To find Diagram for automatic control

Q: The inlet of a centrifugal pump is 7 ft above a water surface level. The reentrant inlet (KIN = 1)…

A: when V  is flow velocity through pipe head required by pump is equal to head loss ue to friction and…

Q: The mounted engine rotates clockwise at pm, The moment of inertia of all the rotating part is 300…

A: A body that rotates about its axis of symmetry will offer resistance to any change in the direction…

Q: (b) Identify the following elements of the given closed loop control system. (1) Process Element…

A: The closed loop system is given by -

Q: 5. In the following typical control system B.D, which block would represent the controller unit:…

A: Controller will regulates the function of other loop elements in given block diagram.  Therefore for…

Q: Define the axis of sight, horizontal axis, and the vertical axis in a total station and describe…

A: The mentioned terminologies are used for a Total station. A Total station is used to measure slant…

Q: Which of the following is correct for a open loop system ? O a. No comparison element O b. Automatic…

A: In an open loop system,

Q: a.explain how a flyball governor works and its relationship to control system. b.Give two practical…

A: A feedback control loop serves as the foundation for the flyball governor. Weighted balls are…

Q: _________________________________is a type of control system in which the process output is…

A:

Q: is design of mechanism to produce a output motion for a given input motion. O a. Analysis, required…

A: Analysis is design of mechanism to produce a required output motion for a given input motion.

Q: Design a hydraulic system for object transferring operation into a furnace using Fluidsim Hydraulic…

A: The circuit is shown below:

Q: MT345, Monday, 11/01/21, O x B Upload Assignment: In-Class E X…

A:

Q: If the load disturbances in flow control systems are rapid and enought to cause the system to…

A: Following is the answer to the above question

Q: Find Inverse Kinematics of the robot in Fig.1 using Graphical method.

A: Given: To find: Inverse kinematics

Q: For mechanical system, terminals with the same displacement must be connected to: a. none of these…

A: When the mechanical system will connected with the same node, then their behavior will be equal and…

Q: 10 is the basic elements of manufacture. C. mechanism 2. The contact type of kinematic pair between…

A: 1] Link is the basic element of manufactureOption Bis correct 2] The contact type of kinematic pair…

Q: Answer all parts show work

A: (a) Drawn the circuit below in step 2(b)Values of the circuit components of this filter is…

Q: Rod AB is bent into the shape of an arc of circle and is lodged between two pegs D and E. . It…

A: Draw the F.B.D of the bend rod AB. As,

Q: 1) Check that mechanism is kinematic chain: L B

A: