10is the basic elements of manufacture.C. mechanism2. The contact type of kinematic pair between two links is point or line-- partB. linkD. machine...contact. This kinematic pair isA. high pairB. low pairC. planar pairD. spatial pair3. A mechanism has 7 links, and there areinstant centers inthis mechanism.А. 42В. 21С. 14D. 284.The standard center distance of a pair of gearsequal to thesum of two reference circles radii.A. must be B. may beC. must not be5. If the teeth number of a standard spur gear is 20, this gearavoid cutter interference,C. can't6. In a crank-slider mechanism, if the average velocities of outgoingstroke and returning stroke are the same, the coefficient of travelA. isn't sure toВ. сanspeed variationА. К%3D1В. К>1C. K<1D. K=2

1] Link is the basic element of manufactureOption Bis correct 2] The contact type of kinematic pair…

10 is the basic elements of manufacture. C. mechanism 2. The contact type of kinematic pair between two links is point or line part В. link D. machine contact. This kinematic pair is A. high pair C. planar pair B. low pair D. spatial pair 3. A mechanism has 7 links, and there are instant centers in this mechanism. A. 42 В. 21 С. 14 D. 28

10 is the basic elements of manufacture. C. mechanism 2. The contact type of kinematic pair between two links is point or line part В. link D. machine contact. This kinematic pair is A. high pair C. planar pair B. low pair D. spatial pair 3. A mechanism has 7 links, and there are instant centers in this mechanism. A. 42 В. 21 С. 14 D. 28

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. The binary number 10101 is equivalent to the decimal number: (a) 19 (b) 21 (c) 35. 2. The decimal number 29 is equivalent to th binary number: (a) 10111 (b) 11011 (c) 11101.
A stepper motor serves as the drive unit for the linear joint of an industrial robot. The joint must have an accuracy of 0.25 mm. The motor is attached to a leadscrew through a 2:1 gear reduction (2 turns of the motor for 1 turn of the leadscrew). The pitch of the leadscrew is 5.0 mm. The mechanical errors in the system (due to backlash of the leadscrew and the gear reducer) can be represented by a normal distribution with standard deviation = ±0.05 mm. Specify the number of step angles that the motor must have in order to meet the accuracy requirement.
1) Check that mechanism is kinematic chain: L
An engineer is designing a transfer line. The line has 15 stations. Stations 1 through 10 should have the same reliability. Each station is expected to operate approximately 1000 cycles between failures. The last 5 stations are expected to break down about once every 600 cycles. Repair times will vary but should average about the equivalent of 12 cycles in duration. a. Find the availability of the line. b. Suppose you could add one buffer of size 20. Where would you place this buffer? Find the increase in availability
FIGURE P1.10 Problems 10 and 35. Decomposition of Planar Linkage Mechanisms into Basic Kinematic Groups(bkgs) Primar,. Dyad, Triad, Quadruple??
instrumentation and control systems
In a belt-pulley system using a flat belt, if the cycle rate = 5, the diameter of the large pulley is 1000 mm, the belt length is 4000 mm, the bending frequency is 4 [1/s], what is the revolution of the small pulley?
1. How many points of contact are used to establish the following datums ? A _____________ B ____________ C _____________ Identify the following items for each of the datum targets :a) the datum reference, b) the specified number on the datum, c) the area size and the shape.
Q12. The simple connecting rod mechanism shown in Figure Q12 has a connecting rod length AB of 142mm and a crank radius OA of 46mm. The connecting rod has a centre of gravity C, which is located 32mm from end A. a) b) c) d) e) When the crank angle 0 is 305° and the crankshaft speed (w) is 6500rpm clockwise as shown, determine by kinematic analysis: The magnitude and direction of the angular velocity of the connecting rod. The magnitude and direction of the velocity of the piston. The magnitude and direction of the angular acceleration of the connecting rod. The magnitude and direction of the acceleration of the piston. The magnitude of the acceleration of the centre of gravity (C) in the X and Y directions. Bo a Fig. 12 Connecting Rod Mechanism A Ꮎ a) b) c) d) e) 131.2 rad/s (ACW) 30.6 m/s to the left 122782.7 rad/s² (ACW) 9953.8 m/s² to the right x: 11712.9 m/s² to the right y: 13524.2 m/s² upwards 4
In control system C(S) denotes the Input of the system. Select one: True False
An incremental optical encoder coupled to a robot wheel has 2880 slots. Find: a) change in angle when 1200 pulses counts are obtained b) number of pulse counts when the angular change is 5000 degrees