A - R – -C -

Q: The system shown is in equilibrium by the applied 250 N-force. Determine the pin reaction D. Neglect…

A: Given data: The applied load is P = 250 N. The horizontal distance between A and O is x = 125 mm.…

Q: Q3. Determine the tension developed in each cord required for equilibrium of the cylinders. F T- 200…

A:

Q: Determine the maximum downward force Pmax that can be applied to wedge A that wil keep the assembly…

A: Given: The weight of block C, W = 192 N

Q: Bar AB of Fig. with weight W and length L has a uniform cross section. The spring has an unstretched…

A: Write the expression of the length of the spring. Write the expression of the change in length of…

Q: For the linkage shown, determine the force Q required for equilibrium when I = 18 in., M = 600…

A: The data given is, The moment on the member, M = 600 Ib.in The angle of inclination, θ= 70° Length…

Q: 6. The system below is fixed at A has a roller at C and contains a hinge at B. Determine the support…

A:

Q: A force P with a magnitude of 240 N is applied to end E of cable CDE , which passes under pulley D…

A: Draw the free-body diagram of the mechanism.

Q: Determine the reactions at A, B, C, and D on the cylinders. Assuming smooth contact surfaces.W1=…

A:

Q: Determine the reactions on rollers at point A and hinge at point B, if the 39.0m and 14.0KN uniform…

A: Draw the FBD for the given figure and question conditions. The weight of the bridge will act at the…

Q: calculate the reactions at A and the tension of cable BC

A:

Q: is negligible. The weight of bar BC of Fig. The spring has an unstretched length L. Determine the…

A: Given data To determine the stability of the spring mass system.

Q: The vertical mast supports the 4.3-kN force F and is constrained by the two fixed cables BC and BD…

A: Givena=5.8mb=3.6mc=2.1mh=5.2m

Q: Given the image below, which force diagrams correctly shjows the reactions at the supports?…

A: Given:-  To Find:-  1- Find the force diagram which correctly shows the reaction at support 2- is…

Q: Two bars and a torsional spring are used to sup- port a mass m as shown in Fig. bars are negligible…

A: Write the expression of the potential energy of the spring.

Q: Question 3 (Type B): A 50 N load is placed onto the personal folding stand. Determine the magnitudes…

A: The load applied isThe surface is frictionless

Q: Determine the reactions at A, B, C, and D on the cylinders. Assuming smooth contact surfaces.W1=…

A: GIVEN:

Q: Static problem: Determine the forces in members DG, EG, and EH by the method of sections. Indicate…

A:

Q: 1. Plate ABCDEF is a sliding door supported by a frictionless linear bearing at A and a frictionless…

A: The total weight of gate is

Q: Determine the force P (MAXIMUM), with which the uniform 18 kg bar will remain in equilibrium.

A:

Q: 6. The system below is fixed at A has a roller at C and contains a hinge at B. Determine the support…

A:

Q: 6. The system below is fixed at A has a roller at C and contains a hinge at B. Determine the support…

A:

Q: (a) Determine the reactions at A and E if P = 420 N. The reactions are positive if to the right or…

A:

Q: The members of a truss are pin connected at joint O. Determine the magnitude of F, and its angle 0…

A: Given data: F2=6 kN Need to determine the magnitude of the force F1 and angle θ.

Q: The spring in Fig. has an unstretched length of 2 ft. Determine the angle e for equilibrium when Wp…

A: k = 350 lb/ft W = 80 lb L = 2 ft Free body diagram of the problem is shown in the figure, Clearly,…

Q: Given the wall crane supports an additional 700 lb. load, the force on the cable at the winch motor…

A:

Q: Member AB is supported by BC and at A by a single journal bearing with a square shaft. Determine the…

A: Free body diagram:Position vector:System A will move up and down, therefore there won't be any…

Q: Cable AB passes over the small ideal pulley C without a change in its tension. What length of cable…

A:

Q: The thrust F of a propeller is generally thought to be afunction of its diameter D and angular…

A: The thrust force is the function of F=fD,ω,V,μ,ρ here n=6m=3 Now the replacing variables are μ,V,D…

Q: Consider the following system in static equilibrium. Force vector Facts at a distance" from the pin…

A: (a) Draw the free-body diagram of bar.

Q: Application of Equilibrium Solve for the value of unknown variables   Given P1 = 1.39 KN P2…

A: Draw the free-body diagram of the beam. (a) As in the beam, no horizontal force is present so that…

Q: Rod AB is attached to a block A that can slide freely in the vertical slot shown. Neglecting the…

A:

Q: Determine the tension developed in wire CD required for equilibrium of the 37 lb cylinder E and the…

A: Given  Weight, WE = 37 lb              WF = 46 lb Find   Tension in CD, TCD

Q: The 15 kg bar AB is supported by a ball and socket joint at A, a smooth wall at B and the cable BC.…

A:

Q: 3. Determine the x, y, z components of reaction acting on the ball-and-socket at A, the reaction at…

A: Given , a plate in which a uniformly distributed load of 40 lb/ft acts from A to B  and a moment of…

Q: QI. Determine the normal reaction at the roller A and horizontal and vertical components at pin B…

A:

Q: 2. A "scale" is constructed with a (5A+4)-ft-long cord and the (20A+5B)-Ib block D. The cord is…

A:

Q: Determine the force in members BC, HC, and HG. After the truss is sectioned use a single equation of…

A: To find: The force in the member BC, HC and HG. Free body diagram: The free body diagram shown…

Q: Determine the force in each member of the truss and state if the member is in tension or…

A:

Q: Determine the force (F) which applied to ring A in order to keep the 250 lb *.cylinder B in…

A: As it is given that cylinder is in equilibrium, then the forces and moments acting on it are in…

Q: The two springs shown in Fig. ther tension or compression and are unstretched when = 0°. Determine…

A: Draw the free-body diagram of the spring-mass system: Now write the moment equation about the…