The 10-kg pipe is supported at A by a system of five cords. Determine the force in the cable AB for equilibrium 60 Select one: a. T(AB) = 593.83 N b. T(AB) = 226.56 N C. T(AB) = 113.28N d. None of these

Q: The uniform plank ABC weighs 40 kg. It is supported by a pin at A and a cable that runs around the…

A:

Q: The gusset plate is subjected to the forces of three members s shown in. The forces are concurrent…

A: To find The magnitude of the tension force in member C.  The angle  Given The force on point O due…

Q: Determine the angle θ for equilibrium of the lever shown in the figure. Disregard the weights of…

A: When all of the forces or moments operating on a structure are balanced, it is said to be in…

Q: Q.2) The windlass is supported by a thrust bearing at A and a smooth journal bearing at B, which are…

A:

Q: Two cylinders are being supported by the wires shown in the figure. Determine the following:   1.1…

A: Given :-  To Find:-  1.1 The tension developed in wire BC required for equilibrium of the 13.6-kg…

Q: Q.3- If block B weighs 325N and block C weighs 175 N, determine the required weight of block D and…

A: We can see the FBD of the joint A

Q: A force P with a magnitude of 240 N is applied to end E of cable CDE , which passes under pulley D…

A: Draw the free-body diagram of the mechanism.

Q: A "scale" is constructed with a 4.1-ft-long cord and the 15-lb block D. The cord is fixed to a pin…

A:

Q: Q4 - Determine the reactions at the supports. 500 N/m www...... B 4 m 4 m 30

A:

Q: The springs in are shown in the equilibrium position. 3m 3 m KAC = 20 N/m KAB = 30 N/m wwwww KAD-40…

A:

Q: The following system is in equilibrium. Draw the free-body diagram of the frame and apply the…

A:

Q: Q2/ Determine the unstretched length of spring AC if a force P = 80lb cause the angle 0 = 60 for…

A: Solution:

Q: 6- When holding the 15-lb equilibrium, the humorous H, assumed to be smooth, exerts normal forces Fc…

A:

Q: Determine the tension developed in each cable for equilibrium of the 300-lb crate. CG 3 ft 6 ft 3 ft…

A:

Q: Determine the magnitude of the reaction at support A, in lb. If: P = 342 lb, h = 19 in., A = 22 in.…

A:

Q: Find the support reactions at the ball and socket 3. support A and the tension, T1 and T2.

A: Given data: F=133 kNCoordinates of A=0, 0, 0Coordinates of B=0, 0, 9Coordinates of C=4, 3,…

Q: Two traffic signals are attached to the_36 ft support cable at equal intervals as shown. Determine…

A: Please find the solution below

Q: Q1: Determine the reactions at the roller F and pin E for the frame loaded as shown. 0.2 m 0.2 m 0.3…

A:

Q: Determine the reactions at supports A and B. A 500 lb/ft -6 ft 6 ft- 700 lb/ft -8 ft- 9 ft 6 ft

A: To find reactions at A and B

Q: The weight W = 9 kN hangs from the cable which passes over the pulley at F. Neglecting the weights…

A: Given data  Given force system

Q: Determine the tension developed in wire CD required for equilibrium of the 37 lb cylinder E and the…

A: Given  Weight, WE = 37 lb              WF = 46 lb Find   Tension in CD, TCD

Q: Q3. The lamp has a weight of (20 - 40 N) and is supported by the six cords connected together as…

A: Please find the tension and angle for maximum weight of the lamp. Given: The maximum and minimum…

Q: Determine the magnitude of the reaction at support A, in lb. If: P = 314 lb, h = 13 in., A = 27 in.…

A:

Q: Q2. Determine the tension developed in each cord required for equilibrium of the 40 kg(F) and 30 kg…

A: Mass of F lamp = 40 kg Mass of G lamp = 30 kg

Q: A "scale" is constructed with a 4.1-ft-long cord and the 13-lb block D. The cord is fixed to a pin…

A:

Q: 5) The system shown is in equilibrium. Find the force exerted on the strut by the hinge at point A.…

A: The combined free-body diagram of the given system is given below:

Q: The beam is supported at A by a pin support and is held in equilibrium by the cable at B. Choose two…

A:

Chemical and Phase Equilibrium

Phase diagrams or equilibrium phase diagrams are the graphical representations that show the phase transformations of the constituting elements with respect to the pressure, temperature, and compositions. The diagrams show the conditions that limit the different phases, namely solid, liquid, and gas. The diagram can also be utilized to verify the relations between the state variables. Most of the phase diagrams are temperature-pressure phase diagrams, with the variable parameter as the composition. Usually other variables such as solubility and pressure parameters are not indicated in the phase diagram. For a one-component system (unary phase diagram), the phase diagram is generally a function of temperature and pressure as the state variables, or temperature and volume. However, for a binary system (two-phase) having two components, the phase diagram is a function of temperature and composition as the state variables only. Coexisting of the different phases of the constituting elements is indicated in the phase diagram. A ternary phase diagram can be characterized by consisting of three phases in equilibrium.