The vertical pole is acted upon by an 8.4kN force. The pole is supported by a ball and socket at A and two cables, BD and BE. Determine the reaction forces at A and the tension in each cable. Show the FBD and use 3D Equations of Equilibrium in Section 5.3. 10 m 5.448 7m 6m C B 6m 6 m

Q: Determine the reactions at support A of the rigid body shown in the image. Also, indicate on your…

A:

Q: QUESTION 1 The 10 kg rod AB is in equilibrium supported by ball-socket A, cable BC and frictionless…

A:

Q: 4000 N 1.0m 2.0 m 20m 2000 N

A: ∑Fx=0Fcosθ+4000=0Fcosθ=-4000N .....(1)∑Fy=0Fsinθ-2000=0Fsinθ=2000 ........(2)

Q: The homogeneous block weights 250 N. Determine the value of P for which the block in equilibrium,…

A: Let us find the value of force P,  first, we draw the free body diagram. the weight acts downward in…

Q: b/2 b

A: according to the given details in the question.  we need to find reactions at A point .

Q: Two forces F1 150 N and F2 50 N to hold the weight of 200 N. Check and determine if the body is in…

A: Equilibrium is a state of a body at which there is no disturbance in a system neither inside nor…

Q: The overhanging beam is supported by a pin at A and the two-force strut BC Determine the horizontal…

A:

Q: The box shown in fig weighs 40O N, in equilibrium Determine the tension in the cords AB and BC

A: Consider the diagram shown below for the given system.

Q: The following system is in equilibrium. Draw the free-body diagram of the frame and apply the…

A:

Q: The pipe assembly supports the vertical loads shown. Determine the components of reaction at the…

A:

Q: If the system shown is to be in equilibrium, determine the following: (a) the tension in cable ABC,…

A:

Q: The vertical mast supports the 6.2-kN force F and is constrained by the two fixed cables BC and BD…

A: Given:The force is .The distances are .The system is shown below.To find:The tension in the cable .

Q: (4): The 14 Kg lamp fixture is suspended from the rings, each having an unstretched length of 7…

A:

Q: The vertical mast supports the 4.3-kN force F and is constrained by the two fixed cables BC and BD…

A: Givena=5.8mb=3.6mc=2.1mh=5.2m

Q: Q- Two radial 200 N and 500 N forces and tangential 700 N force are applied to shown system. If the…

A: Draw a labeled free-body diagram of the given system. Calculate angle Ɵ, θ=sin-11.1 m2 m=33.37°…

Q: Q2/ Determine the unstretched length of spring AC if a force P 801b causes the angle 0 = 60° for…

A: Solution:

Q: Determine the magnitude of the reaction at support A, in lb. If: P = 342 lb, h = 19 in., A = 22 in.…

A:

Q: Cable AB passes over the small ideal pulley C without a change in its tension. What length of cable…

A: Given data: ◆ The tension in the rope ABC = 74 lb ◆ The angle made by cable ABC with horizontal =…

Q: The forces and all lengths are given in the image. If the pile is in equilibrium, find out all…

A: Given figure  To determine all support reaction components at the fixed support O.

Q: Cable AB passes over the small ideal pulley Cwithout a change in its tension. What length of cable…

A: Given:  m= 75 lb θ=41o Tension T in cable CD=? Cable AB passes over the small ideal pulley C without…

Q: Problem 3: Each cord can sustain a maximum tension of 500 N. Determine the largest weight of the…

A:

Q: 1. Plate ABCDEF is a sliding door supported by a frictionless linear bearing at A and a frictionless…

A: The total weight of gate is

Q: The mass center G of the 1470-kg rear-engine car is located as shown in the figure. Determine the…

A:

Q: The sign has a mass of 100 kg with a center of mass at G. Determine the components of the reaction…

A: Write the point vectors for each point. A=0, 0, -0.5B=0, 2, 0C=1, 0, 2D=-2, 0, 1 Write the vectors…

Q: 3. A 3500 lb motor and plate, as shown, are in equilibrium and supported by three cables and d = 4…

A:

Q: Y pies FD Fs D X 0,6 m FA W

A:

Q: Show the complete solution: Two cables tied together as shown in figure , Knowing that Q = 60 lbs…

A: Consider the free body diagram of the point C.

Q: If the weight of homogenous bar AB is 10kN, F is 40kN, and bar AB is in equilibrium, calculate the…

A:

Q: Determine the force in cables AB, AC, CD, CE, and CF needed to support the 500-lb crate. Complete…

A: The weight of crate is

Q: On a horizontal beam AB with a length of 4 m, a force F of 5 kN acts at point A. The beam is hinged…

A:

Q: Member AB is supported by a cable BC and at A by a square rod which fits loosely through the square…

A:

Q: Draw the free-body diagram The plate is made of steel which has a density of 7850 kg If the…

A: Given Data Density of steel plate is : ρ=7850 kg/m3 Thickness of the plate is :t=1 cm=0.01 m Now a…

Q: D 3 m 2 m A 4 m B E F AB= F(AB)=tension force in AB F= F(AD)=tension force in AD AD F =…

A:

Q: Cable AB passes over the small ideal pulley C without a change in its tension. What length of cable…

A:

Chemical and Phase Equilibrium

Phase diagrams or equilibrium phase diagrams are the graphical representations that show the phase transformations of the constituting elements with respect to the pressure, temperature, and compositions. The diagrams show the conditions that limit the different phases, namely solid, liquid, and gas. The diagram can also be utilized to verify the relations between the state variables. Most of the phase diagrams are temperature-pressure phase diagrams, with the variable parameter as the composition. Usually other variables such as solubility and pressure parameters are not indicated in the phase diagram. For a one-component system (unary phase diagram), the phase diagram is generally a function of temperature and pressure as the state variables, or temperature and volume. However, for a binary system (two-phase) having two components, the phase diagram is a function of temperature and composition as the state variables only. Coexisting of the different phases of the constituting elements is indicated in the phase diagram. A ternary phase diagram can be characterized by consisting of three phases in equilibrium.