Water enters an adiabatic nozzle steadily at 500 kPa and 300˚C with a mass flow rate of 6000 kg/h and leaves at 100 kPa and 45 m/s. The inlet area of the nozzle is 40 cm2. Take the Cp of CO2 to be 4.2 kJ/kgK and the specific volume of water to 0.001 m3/kg. Determine the inlet velocity and the exit temperature.

Water enters an adiabatic nozzle steadily at 500 kPa and 300˚C with a mass flow rate of 6000 kg/h and leaves at 100 kPa and 45 m/s. The inlet area of the nozzle is 40 cm2. Take the Cp of CO2 to be 4.2 kJ/kgK and the specific volume of water to 0.001 m3/kg. Determine the inlet velocity and the exit temperature.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Steam enters a diffuser at 20 psia and 240°F with a velocity of 900 ft/s and exits as saturated vapor at 240°F and 100 ft/s. The exit area of the diffuser is 1 ft2 . Determine the mass flow rate of the steam.
Air (MW=29 g/mol) at 115.00 kPa and 285.00 is compressed steadily to 600.0 kPa. The mass flow rate of the air is 2.00 kg/s and a heat loss of 32.1 kW occurs during the process. You may assume that changes in kinetic and potential energy are negligible, the temperature of the surroundings is 25 ∘C, and that the CP of air is 3.5 R. Given the compressor operates with a second law (reversible) efficiency of 0.60,calculate the following. What is the actual work interaction term in kW? What is the actual exit temperature of the air in Celcius?
Air at 15°C and 95 kPa enters the diffuser of a jet engine steadily with avelocity of 250 m/s. The inlet area of the diffuser is 0.5 m2. The air leaves thediffuser with a velocity that is very small compared with the inlet velocity.Determine The following:1- The mass flow rate of the air2- The temperature of the air leaving the diffuser3- The power and rate of heat transfer within the diffuser.
Refrigerant-134a enters a diffuser steadily as saturated vapor at 700 kPa with a velocity of 150 m/s, and it leaves at 800 kPa and 50°C. The refrigerant is gaining heat at a rate of 5kJ/s as it passes through the diffuser. If the exit area is 70 percent greater than the inlet area, determine (a) the exit velocity and (b) the mass flow rate of the refrigerant.
Steam at 1100 kPa and 92 percent quality is heated in a rigid container until the pressure is 2000 kPa. For a mass of 0.05 kg. calculate the amount of heat supply (in kJ) and the total entropy change (in kJ/kg.K).
Steam enters a diffuser at 10 kPa and 60°C with a velocity of 375 m/s and exits as saturated vapor at 50°C and 70 m/s. The exit area of the diffuser is 3 m2 . Determine the mass flow rate of the steam.
Q: Five hundred kilograms per hour of steam drives a turbine. The steam enters the turbine at 44 atm and 450°C at a linear velocity of 60 m/s and leaves at a point 5 m below the turbine inlet at atmospheric pressure and a velocity of 360 m/s. The turbine delivers shaft work at a rate of 70 kW, and the heat loss from the turbine is estimated to be 10ʻ kcal/h. Calculate the specific enthalpy change associated with the process.
Air enters the turbine at 1 MPa and 327 degree* C with a velocity of 100 m/s and exits at 100 kPa and 27 degree*C with a low velocity. Heat transfer loss from the turbine surface is 1200kJ / min and the power output of the turbine is 240 kW. Determine the mass flow rate of air through the turbine.
A pump increases the water pressure from 8 kPa at the inlet to 700 kPa at the outlet. Water enters this pump at 41.51°C through a 1.704-cm-diameter opening and exits through a 1.154-cm-diameter opening. Determine the velocity of the water at the outlet in m/s when the mass flow rate through the pump is 1.101 kg/s. The specific volume of incoming water is 1.426 × 10-3 m3/kg.
A 1.8kg/s of steam expands in a turbine producing 550 kW of power output. The steam enters at a velocity of 18 m/s and exits at 70 m/s. The reduction of specific enthalpy is 400 kJ/kg. Determine that the heat flow per second when the inlet of the turbine is located 900mm above the outlet.
Air is compressed by an adiabatic compressor from 100 kPa and 20°C to 1.8 MPa and 400°C. Air enters the compressor through a 0.15- m² opening with a velocity of 30 m/s. It exits through a 0.084-m² opening. Calculate the mass flow rate of air and the required power input. The constant pressure specific heat of air at the average temperature of 210°C = 483 K is cp= 1.026 kJ/kg-K. The gas constant of air is R = 0.287 kPa-m³/kg-K. 3 The mass flow rate of air is The required power input is kg/s. KW.
use direct formula