"II-1 The shaft shown in Figure P11-I was designed in Problem 10-1. For the data in the row(s) assigned from Table P11-1, and the corresponding diameter of shaft found in Problem 10-1, design suitable bearings to support the load for at least 7E7 cycles at 1500 rpm. State all assumptions. (a) Using hydrodynamically lubricated bronze sleeve bearings with Ox = 20, 1/d=1.25, and a clearance ratio of 0.001 5. assume bearings act as simple supports FIGURE P11-1 Shaft Design for Problem 11-1 11-2 The shaft shown in Figure P11-2 was designed in Problem 10-2. For the data in the row(s) assigned from Table P11-1, and the corresponding diameter of shaft found in Problem 10-2, design suitable bearings to support the load for at least 3E8 cycles at 2.500 rpm. State all assumptions. (a) Using hydrodynamically lubricated bronze sleeve bearings with ON=30, 1/d=1.0, and a clearance ratio of 0.002. FIGURE P11-2 Shaft Design for Problem 11-2 Table P11-1 Data for Problems assume bearings act as simple supports Row D Pap a 20 16 18 1000 ° Tmas 2000 b 12 2 7 500 -100 600 c 14 4 12 750 -200 400 d 8 4 B 1000 2000 17 6 12 1500 -200 500 24 16 22 750 1000 2000
"II-1 The shaft shown in Figure P11-I was designed in Problem 10-1. For the data in the row(s) assigned from Table P11-1, and the corresponding diameter of shaft found in Problem 10-1, design suitable bearings to support the load for at least 7E7 cycles at 1500 rpm. State all assumptions. (a) Using hydrodynamically lubricated bronze sleeve bearings with Ox = 20, 1/d=1.25, and a clearance ratio of 0.001 5. assume bearings act as simple supports FIGURE P11-1 Shaft Design for Problem 11-1 11-2 The shaft shown in Figure P11-2 was designed in Problem 10-2. For the data in the row(s) assigned from Table P11-1, and the corresponding diameter of shaft found in Problem 10-2, design suitable bearings to support the load for at least 3E8 cycles at 2.500 rpm. State all assumptions. (a) Using hydrodynamically lubricated bronze sleeve bearings with ON=30, 1/d=1.0, and a clearance ratio of 0.002. FIGURE P11-2 Shaft Design for Problem 11-2 Table P11-1 Data for Problems assume bearings act as simple supports Row D Pap a 20 16 18 1000 ° Tmas 2000 b 12 2 7 500 -100 600 c 14 4 12 750 -200 400 d 8 4 B 1000 2000 17 6 12 1500 -200 500 24 16 22 750 1000 2000
Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)
8th Edition
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Kreith, Frank; Manglik, Raj M.
Chapter4: Numerical Analysis Of Heat Conduction
Section: Chapter Questions
Problem 4.49P
Related questions
Question
100%
Transcribed Image Text:"II-1 The shaft shown in Figure P11-I was designed in Problem 10-1. For the data in the
row(s) assigned from Table P11-1, and the corresponding diameter of shaft found in
Problem 10-1, design suitable bearings to support the load for at least 7E7 cycles at
1500 rpm. State all assumptions.
(a)
Using hydrodynamically lubricated bronze sleeve bearings with Ox = 20,
1/d=1.25, and a clearance ratio of 0.001 5.
assume bearings act
as simple supports
FIGURE P11-1
Shaft Design for Problem 11-1
11-2 The shaft shown in Figure P11-2 was designed in Problem 10-2. For the data in the
row(s) assigned from Table P11-1, and the corresponding diameter of shaft found in
Problem 10-2, design suitable bearings to support the load for at least 3E8 cycles at
2.500 rpm. State all assumptions.
(a)
Using hydrodynamically lubricated bronze sleeve bearings with ON=30,
1/d=1.0, and a clearance ratio of 0.002.
FIGURE P11-2
Shaft Design for Problem 11-2
Table P11-1 Data for Problems
assume bearings act
as simple supports
Row
D
Pap
a
20
16
18
1000
°
Tmas
2000
b
12
2
7
500
-100
600
c
14
4
12
750
-200
400
d
8
4
B
1000
2000
17
6
12
1500
-200
500
24
16
22
750
1000
2000
Expert Solution
This question has been solved!
Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.
Step by step
Solved in 2 steps with 11 images
Recommended textbooks for you
Principles of Heat Transfer (Activate Learning wi…
Mechanical Engineering
ISBN:
9781305387102
Author:
Kreith, Frank; Manglik, Raj M.
Publisher:
Cengage Learning
Precision Machining Technology (MindTap Course Li…
Mechanical Engineering
ISBN:
9781285444543
Author:
Peter J. Hoffman, Eric S. Hopewell, Brian Janes
Publisher:
Cengage Learning
Automotive Technology: A Systems Approach (MindTa…
Mechanical Engineering
ISBN:
9781133612315
Author:
Jack Erjavec, Rob Thompson
Publisher:
Cengage Learning
Principles of Heat Transfer (Activate Learning wi…
Mechanical Engineering
ISBN:
9781305387102
Author:
Kreith, Frank; Manglik, Raj M.
Publisher:
Cengage Learning
Precision Machining Technology (MindTap Course Li…
Mechanical Engineering
ISBN:
9781285444543
Author:
Peter J. Hoffman, Eric S. Hopewell, Brian Janes
Publisher:
Cengage Learning
Automotive Technology: A Systems Approach (MindTa…
Mechanical Engineering
ISBN:
9781133612315
Author:
Jack Erjavec, Rob Thompson
Publisher:
Cengage Learning
International Edition---engineering Mechanics: St…
Mechanical Engineering
ISBN:
9781305501607
Author:
Andrew Pytel And Jaan Kiusalaas
Publisher:
CENGAGE L
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:
9781337093347
Author:
Barry J. Goodno, James M. Gere
Publisher:
Cengage Learning
Understanding Motor Controls
Mechanical Engineering
ISBN:
9781337798686
Author:
Stephen L. Herman
Publisher:
Delmar Cengage Learning