VCVcBSTDC-BDCSTQTp = Pg A (asne) [1+ % CUSA]At what position (in degrees after top dead center) wouldyou want the peak pressure of combustion to occurto create the maximum torque on the crankshaft?For a 100mm piston digimeter acting on a connecting.rod with a length of 80mm use the equationabove to calculate the torque (NIM) on thecrankshaft at this crank position for an enginethat develops a peak pressure of 135 bar

Answered: VC Vc B S TDC -BDC S TQ Tp = Pg A…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Can you help with question2
Find the piston size of a 4-stroke, 4-cylinder engine, given the following Crankshaft rotation = 2500 rpm Mean Effective Pressure = 162 psi Indicated horsepower = 125 Bore-stroke ration = 1:1.5
Q2 An automotive engine has a bore of 90 mm; the stroke is 110 mm; and the length of the connecting rod is 166 mm Knowing that the volume of the combustion chamber is 75 cm³ and the intake valve closes 18° crank angle degree after BDC. If injection Started 10 degrees before TDC and ends 40 degree after TDC. And the engine is running at 3000 rpm. a. Calculate the geometrical compression ratio and the actual compression ratio? b. Find the ratio between the maximum speed of the piston to the mean piston speed for this engine? c. Find the injection period
3.1 A 3 liters S.I. V6 engine that operates on a four-stroke of 3000 revolution per minute, the compression ratio is 10, the lengths of the connecting rod and the crank offset are 15 cm and 4 cm respectively, the combustion is completed at 35° of the crankshaft rotation after I need an answer as soon as possible, and I hope it will be clear. Greetings, my bro. TDC, the engine is running with the stoichiometric air-fuel ratio, mechanical efficiency 90%. If the engine is connected to a dynamometer which its reading of 100 kW. Calculate: 1-piston speed at end of the combustion, 2-volume of the combustion chamber at end of the combustion, 3-engine torque, 4- indicated mean effective pressure and 5-break specific fuel consumption.
Find the Fthrust and Frictional force using the following info attached gr 11 MAss of 4 full engines - 42.13g empty engines- 75.65g
Seatwork No. 1 An SI I-2 square engine operates on a 2-stroke cycle at 2400 rpm. The average piston speed is 15 m/se and the no. of piston action is 2. When the piston is at its maximum position the remainder volume is 0.005 Liters. Determine: a. Volumetric displacement per unit time for all cylinders (m³/sec) b. Compression ratio c. Volume at Bottom Dead Center (m³)
As shown in Fig., the working area of cylinder head side A=50cm, working load F=10000N, the setting pressure of the valve 1 is 5MPA, and the setting pressures of the valve 2 is 3MPA. Please answer the following questions: 1) What's the pressure at point A and B respectively when piston of the cylinder is moving forwards at the working speed. Please give the reason." 2) What's the pressure at point A and B respectively when piston of the cylinder reaches and stops at the end. Please give the reason.
Q3: You are designing a four-stroke cycle diesel engine to provide a brake power of 300 kW naturally aspirated at its maximum rated speed. Based on typical values for bmep and maximum mean piston speed, estimate the required engine displacement, bore and stroke for sensible cylinder geometry, also find the number of engine cylinders. What is the maximum rated engine speed (rev/min) for your design? What would be the brake torque (N-m) and the fuel flow rate (g/hr) at this maximum speed? Assume a maximum mean piston speed of 12 m/s is typical of good engine designs.
1. A six-cylinder two-stroke engine with a compression ratio = 9 produces a torque of 1100 Nm at a speed of 2100 rpm. It has a bore bof 123 mm and a stroke s of 127 mm. (a) What is the displacement volume and the clearance volume of a cylinder? (b) What is the engine bmep, brake power, and mean piston speed?
STEAM ENGINE PROBLEM. Please solve carefully/ellaborately and include the untis in every step, show diagram and write your solutions clearly and must be readable if your solution is in written form. Your work will be appreaciated much. Thank You.
i need the answer quickly
Question: Please compute the compression ratio of an engine that has a bore of 5 inches and a stroke of 5 inches when the volume at the combustion chamber is 16.36 cubic. in. with the piston at TDC. Please provide a complete solution. Thak you!

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS