VBIAS O VI O CM 11 ↓ M2 M1 RS ∞ MI HH"¹ RL CL Vo Given values: ID k VTH VA Vov,M₁ RS RL CM CL 50 μα 1.5 mA/V2 0.60 V 60 V 0.25 V 7.5 ΚΩ 100 ΚΩ 100 pF 10 nF 1. Draw the small-signal equivalent model of the circuit. Assume ro →∞ for both M1 and M2. NOTE: USE THE DERIVED TWO-PORT MODEL OF M₁ WITH RS. IN ADDITION, CM AND CL WILL BE INCLUDED IN THE SMALL SIGNAL MODEL. 2. Derive the transfer function() and determine the location of the pole and zero frequencies. 3. Determine the gain (in dB) at DC and at the pole and zero frequencies.

VBIAS O VI O CM 11 ↓ M2 M1 RS ∞ MI HH"¹ RL CL Vo Given values: ID k VTH VA Vov,M₁ RS RL CM CL 50 μα 1.5 mA/V2 0.60 V 60 V 0.25 V 7.5 ΚΩ 100 ΚΩ 100 pF 10 nF 1. Draw the small-signal equivalent model of the circuit. Assume ro →∞ for both M1 and M2. NOTE: USE THE DERIVED TWO-PORT MODEL OF M₁ WITH RS. IN ADDITION, CM AND CL WILL BE INCLUDED IN THE SMALL SIGNAL MODEL. 2. Derive the transfer function() and determine the location of the pole and zero frequencies. 3. Determine the gain (in dB) at DC and at the pole and zero frequencies.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Please show each step with the formulas used
In order to design an square wave oscillator with 50% duty cycle of the period of 1 second. Specify the values of R1, R2, and C1, C2 in Astable Multivibrator using 555 timers.
Given that Izk=1mA, IzM = 100 mA, Zz = 52 and Vz = 6V@10mA, Rs=300 2. Find a minimum allowed input voltage. a) 5.7 V b) 6.3V c) 7.7V d) 10.3V e)12.1V Vour b e
In a stair step A/D converter, clock frequency is 1 MHz, threshold voltage is (0.1 V). The full scale output of D/A converter is (10.23 V). If it is a 10 bit device. Find the conversion time for an analog input of (3.728 V)? 373 UG
I need the answer as soon as possible
A carrier signal with frequency of 1 MHz and peak-to-peak amplitude of 10√2v is added to a single tone message with frequency of 1 kHz and peak-to-peak amplitude of 4√2v. Then passed through a diode having the following c/cs: i(t) = e(t) + 0.5e²(t), find: 1- Modulation depth of DSB signal. 2- Frequency of each component in the diode current.
HW 1)find the oufputof the Sxstena hcn)=2ucn-1) iR its input xcn) =()"u() %3D
2. For the given circuit, 6 = 100 and VBe = 0.7 V, determine IB, VCe, VB, Vc, Ve %3D vcc 18V VCC R1 47k2 R4 2k2 2 R3 1 2kQ BJT_NPN_VIRTUAL 3 R2 R5 10k2 1kQ 4.
An RC filter stage (R = 42 Ω, C = 220 µF) is used to filter a signal of 30 V dc with 6 V rms operating from a full wave rectifier. Calculate the percentage ripple at the output of the RC Section for a 200-mA load. Also calculate the ripple of the filtered signal applied to the RC stage.
b-Low input impedance c-Low input capacitance d-Higher gm 6-To get a negative gate-source voltage in a self-biased JFET circuit, you must have a a-Voltage divider b-Source resistance e-Ground d-Negative gate supply voltage 7-When a JFET is cut off, the depletion layers are a-Touching b-Conducting c-Close together d-Far apart. 8-A D-MOSFET can operate in the a-Depletion-mode only b-Enhancement-mode only c- Depletion-mode or Enhancement-mode. d-Low-impedance mode 9-The voltage gain of a D-MOSFET amplifier is dependent on a-Rp b-RL c-gm d-All of the above.
Assume Is = 8 x 10-16 A, B = 100, VT= 26mV and VA =00, For the circuit shown below and for I1= 3 mA, the value of the transconductance is %3D Vcc=2 V + VB Select one: a. 19.23 mA/V b. None of these C. 76.92 mA/N d. 115.38 mAN e. 38.46 mA/W
Plz solve in 30 min I vill upvote and vill give positive feedback