Consider a shunt linear regulator with Vin = 10V, Pz = 500mW, Vz= 2.5V and current limiting IR1(max) = 100 mA. Design a parallel regulator to yield a regulated output VOUT = 5.0 V. 10 V VINO VREF R₂ VEZDI www R₁ b) 0.5 W, 50% c) 1 W, 25% d) 1 W, 50% e) None of the above 2₁ a www Ry Vx 5 ΚΩ VouT 5V What is the rating (in Watts) for R₁ and efficiency of this linear regulator? a) 0.5 W, 25%

Consider a shunt linear regulator with Vin = 10V, Pz = 500mW, Vz= 2.5V and current limiting IR1(max) = 100 mA. Design a parallel regulator to yield a regulated output VOUT = 5.0 V. 10 V VINO VREF R₂ VEZDI www R₁ b) 0.5 W, 50% c) 1 W, 25% d) 1 W, 50% e) None of the above 2₁ a www Ry Vx 5 ΚΩ VouT 5V What is the rating (in Watts) for R₁ and efficiency of this linear regulator? a) 0.5 W, 25%

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For the given circuit below, it operates on a peak-to-peak input voltage of 347.1 V, F = 60 Hz household supply through a step- down transformer with turns N1 = 10 and N2 = 1. Silicon diodes are used with a 1 Kiloohms load. Determine the output peak voltage (in volts). D1 D2 AC Input Vsec B (source) D3 D4 Load 24.30 15.96 12.40 O 18.75
piscussion:- 1. Sketch Vo 20 V -20 v 2. Design a diode clamper to generate the Vo fromV 10v 2.7V UNIVERSITY - L0v -17.3
Specify the LM-series linear regulator required to regulate a fixed voltage of -19 V. Please write the numbers only in the answer field: i.e. for LM1234, you would write 1234 in the answer field.
Tunnel diode is used as a very fast switching device in computers and also used in high frequency oscillators and amplifiers. Select one: True O False
The following figure represents the energy band alignment of Conduction Band (CB)- Valence Band (VB) Lütfen birini seçin: O homojunction. type I heterojunction. Semimetal. type II heterojunction.
Attampet with only two: 1: Prove that the dynamic resistance of diode is ra=26mv/Ip. 2:Prove that the ripple voltage of HWR is Viru=V+Vde and the ripple factor of HWR 121%, u=40.5%. 3: Using silicon diode design a clamper that will produce output V-20Sin wt+10 (v) when the input voltage is Vo=20Sin wt-10 (V).Draw the circuit diagram and the input and output signals. 4:The 6-V zener diode has a maximum rated power dissipated of 690 mw.Its reveres current must be at least 3mA to keep it in breakdown. Find a suitable value for Rs if V; can vary from 9v to 12v and Ri. can vary from 5000 to 1.2KO.
Q2 In step-down regulator in Figure below, calculate the output voltage if the switching frequency is 76.923 kHz and the capacitor discharging time is 7 us. What happen to the output voltage if the discharging time of the capacitor increased to 9 us? Variable pule-width modulutor Comparator Enor signal Va
A 60 V peak full-wave rectified voltage is applied to a capacitor-input filter. If f = 49 Hz, R = 9 kn, and C = 80 μF, the ripple voltage is Choose... Vpp
Consider a shunt linear regulator with Vin = 10V, Pz = 500mW, Vz= 2.5V and current limiting IR1(max) = 100 mA. Design a parallel regulator to yield a regulated output VOUT = 5.0 V. 10 V VINO VREF R₂ VEZDI www R₁ b) 0.5 W, 50% c) 1 W, 25% d) 1 W, 50% e) None of the above 2₁ a www Ry Vx 5 ΚΩ VouT 5V What is the rating (in Watts) for R₁ and efficiency of this linear regulator? a) 0.5 W, 25%
A step down converter is operated with a duty cycle of k = 0.75. The input voltage is Vs = 20V, and the load is: L = 5mH, R = 1502. The minimum inductor current is I₁ = 0.1A. The maximum inductor current is: Select one: a. 1.9 A b. None of these OC. 0.9 A O d. 1.1 A Oe. 2 A
double clipper circuit Zener diodes 1N4733A has a voltage of 5.1 V and 1N4735A has a voltage of 6.2 V with a resistor R=300ohms has been used. you may like to increase the input to a 12 VRMS AC source in order to see the clipping at 7volt. Please, Do the theoretical calculations and plot the expected waveforms by hand. ( I have its multisim design and only needs theoretical calculation and hand drawn graph of it to compare to its data that I have collected from multism.) Thanks
1.Find condition to know Diode on or off, Von = 0.7V. 2 Find relative equation between Vo and Vin