If the diode resistance is 1.2 ohms, source resistance is 0.3 ohms, loadresistance is 1.5 ohms, and capacitor value is 0.47 uF:AM signal xe(t)RsD₁RLVoutFigure 1: The Envelope DetectorWill the envelope detector work just fine with its current specifications? Choosethe best action/s or reasoning/s. (Select one or more)e) Yes, but the diode model should be changed.f) No, the diode resistance needs to be adjusted.a) Yes, but the capacitor value should be increased for better performance.b) Yes, but the capacitor value should be decreased for better performance.c) No, the load resistance should be adjusted.d) No, the source resistance should be adjusted.

Given: Required: Envelope detector specifications.

Will the envelope detector work just fine with its current specifications? Choose the best action/s or reasoning/s. (Select one or more) a) Yes, but the capacitor value should be increased for better performance. b) Yes, but the capacitor value should be decreased for better performance. c) No, the load resistance should be adjusted. d) No, the source resistance should be adjusted. e) Yes, but the diode model should be changed. f) No, the diode resistance needs to be adjusted.

Will the envelope detector work just fine with its current specifications? Choose the best action/s or reasoning/s. (Select one or more) a) Yes, but the capacitor value should be increased for better performance. b) Yes, but the capacitor value should be decreased for better performance. c) No, the load resistance should be adjusted. d) No, the source resistance should be adjusted. e) Yes, but the diode model should be changed. f) No, the diode resistance needs to be adjusted.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
True or False. Please explain. thank you As the temperature increases, the forward voltage decreases in a silicon diode. Then, the graph of the forward bias region will shift to the left.
4. An RC filter stage (R = 33 0, C = 120 HF) is used to filter a signal of 24 V dc with 2 V rms operating from a full wave rectifier. Calculate the percentage ripple at the output of the RC Section for a 100-mA load. Also calculate the ripple of the filtered signal applied to the RC stage. *****END*****
uo A:EV * ll. pluli ► b89f3244-f736-4021-901... PI EXPlain The effect of increasing The filter Capacitance on The outfut Voltage in The haif - wave rectifier and filber Circuit ? CS Scanned with CamScanner
Tnch.jsp?course_assessment_id%3_34730_18&course_id%3D_56188_1&content id%3 17132 Remaining Time: 46 minutes, 56 seconds. Question Completion Status: -30V-- QUESTION 5 Assuming the practical model of the diode, what is the output waveform for the circuit given below. R 2.2 kN +30 V Vin OV- DIV DA Vout -30 V A1L Anguers to saue all answers.
Repeat example 35 for FWD and firing angle Fa) 60°. 215 l65 D1985 Example 35: A full wave rectifier used 220V, with firing angle 10° ,total resistance load 5 KQ, inductance 2.34 H,and frequency 60HZ, Draw and calculate: (a) VD.c and Ipc (b) VD.C(Max) (c) Vn (d) Vorms-
In the circuit shown below. Determine the following a. Vs (at the secondary) b. Vout (across RL) c. Vrip (ripple votage) d. VDC e. PIV (Peak Inverse Voltage) 10:1 Output 115 V mis 60 Hz RL 2.2 k) D, 50μF- All diodes are IN4001. Tund AlMannai EENG261 Page 5/11
Example Full wave rectifier)) for the signal shown plot the amplitude specturm -T=0.4 for 2.6M²/ 5.41 weez fo -5T redbr ~0.4 -0.2 XCD) Vm 0.2 0.4
What will be the out put of the H.W.R+PMMC meters, if an average responding a.c meter of half-wave rectifier read (2.36 v), and true form factor of input waveform is (1.414), * 2.36 V 4.71 V O 1.11 V 3 V
Create the Diode Characteristic Curve for this data values. Diode Voltage (VD) Diode Current (ID) 0.890904 9.109 0.884515 7.115 0.876023 5.124 0.86333 3.137 0.837654 1.162 0.793023 0.206975 0.779114 0.120885 0.754079 0.04592 0.695273 0.004727 0.599882 0.000118256 0.499998 0.000002487 0.4 5.2464E-08 0.3 1.39E-09 0.2 2.23008E-10 0.1 1.00568E-10 0 0 -0.1 -1.0011E-09 -0.2 -2.00211E-09 -0.3 -3.0031E-09 -0.4 -4.00411E-09 -0.5 -5.0051E-09 -0.6 -6.0061E-09 -0.7 -7.0071E-09 -0.8 -8.0081E-09 -0.9 -9.00911E-09 -1 -1.001E-08 -2 -2.002E-08 -4 -4.004E-08 -6 -6.006E-08 -8 -8.008E-08 -10 -1.001E-07 -20 -2.002E-07 -40 -4.004E-07 -60 -6.006E-07 -80 -8.008E-07 -100 -0.000001001 -200 -0.000002002 -300 -0.000003003 -400 -0.000004004 -500 -0.000005005
Solve it fast fast plz
Design a full-wave bridge type power supply. Design the transformer, filter and regulator section. For the rectifier part, choose diode with appropriate PIV rating. Use standard values for your design. The output dc voltage should be 7.5 V and the Maximum output power be 20 mW. Use the topology below as reference