Using Mohr's Circle, solve Review problem R9-5 in the 10th Ed. of the text. Plot your solution along with notation of the axes and all the values below on graph paper. Show your calculation for the values below. 1. Find the Principal Stresses, and the orientation of the element at the those stresses 2. Find the maximum in plane shear stress, and the orientation of the element at that stress 3. Find the absolute maximum in plane shear stress 4. Find the normal stresses and shear stress when the element is rotated 30 degrees counterclockwise

Using Mohr's Circle, solve Review problem R9-5 in the 10th Ed. of the text. Plot your solution along with notation of the axes and all the values below on graph paper. Show your calculation for the values below. 1. Find the Principal Stresses, and the orientation of the element at the those stresses 2. Find the maximum in plane shear stress, and the orientation of the element at that stress 3. Find the absolute maximum in plane shear stress 4. Find the normal stresses and shear stress when the element is rotated 30 degrees counterclockwise

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Use Mohrs circle to find the principle stresses and determine the normal and shear stresses acting on a plane 45 degrees counter clockwise from the Y-plane. Sketch showing the exterior stresses.
Mohr's circle is shown for a point in a physical object that is subjected to plane stress. Each grid square is 160 psi in size. (a) Determine the stresses Ox, Oy, and the magnitude of Txy and show them on a stress element. (b) Determine the principal stresses and the magnitude of the maximum in-plane shear stress acting at the point and show these stresses on an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16). Answer: (a) ox= i i Øy= Txy = = (b) Op1 Op2= i Mi Mi Tmax in-plane= y Mi C psi psi psi X psi psi psi
A state of plane stress is illustrated in the stress element in Figure 3. (a) (b) 30 MPa Figure 3. 40 MPa 60 MPa y X Find the center, X and Y of the Mohr circle. Plot the Mohr circle using these points. From the Mohr circle, find the principal stress and the maximum shear stress. Indicate on the Mohr circle where these values are found.
Determine the state of stress of a beam at the point shown in Figure 2 to represent: a) the principal stresses; b) the maximum in-plane shear stress and the associated average normal stress. c) For each of the two cases mentioned in (a) and (b), determine the corresponding orientation of the element with respect to the original element shown and sketch the results relative to the longitudinal axis of the beam. Please show the full working to provide sufficient information for the sketching to be complete. 15MPa Figure 2 20° 50MPa
The state of stress at a point in a machine component is given by ox = 120 MPa, oy = 55 MPa, Oz = -85 MPa, Oxy = -55 MPa, Oxz = -75 MPa, and oyz = 33 MPa. Construct the Mohr's circles of stress for this stress state and find the maximum shear stress.
From the stress states in a Cartesian coordinate system, the following tensors are obtained:σxy = [100-100-100-800)]. Determine and graph the principal stresses and the directions associated with them using the mohr's circle. determine and graph the maximum shear stresses graph the possible failure planes finally, what is the value of the maximum tangential stress and in what orientations does it take place?
In a stressed element, the value of normal stress along 'X' and 'Y' directions are 250 MPa (tensile) and 125 MPa (tensile) respectively and no shear stress is acting on the plane. Find the Normal stress, if the position of principal plane is 0° to major axis. The normal stress in MPa =
Problem 3. Strains are measured on the surface of a structural component as &A = = 1200 x 10-6. EB = 500 x 10-6, &c = 300 × 10-6. E = 200 GPa and v = 0.3. b) a) Find the principal stresses and show these on a sketch of a properly oriented element. Use Mohr's Circle to find the stresses at 0 = 30° counterclockwise from the x axis and show these on a sketch of a properly oriented element. y 60° C B A X
The following stress condition is applied to a cubic material.Normal stress in the x direction is 15 Mpa, normal stress in the z direction is -7 Mpa and the shear stress in the x-z plane is 59 Mpa.(a) Write the stress tensor(b) Find the maximum normal stress(c) Find the angle with respect to the x- axis at which the maximum normal stress is applied(d) Find the maximum shear stress(e) Determine the angle with respect to the x-axis at which the maximum shear stress is experienced
Part C - Counterclockwise Rotation of a Stress Element The state of stress at a point in a member is shown on the rectangular stress element in (Figure 5) where the magnitudes of the stresses are |o₂| = 16 ksi, |oy| 29 ksi, and Try = 8 ksi Determine the state of stress on an element rotated 50° counterclockwise from the element shown. Express your answers, separated by commas, to three significant figures. ► View Available Hint(s) 02 Oy, Tz'y' Submit - VE ΑΣΦ ↓↑ vec Part D-Clockwise Rotation of a Stress Element with No Shear Stress ? ksi, ksi, ksi The state of stress at a point in a member is shown on the rectangular stress element in (Figure 6) where the magnitudes of the stresses are ₂ = 13 ksi and|oy| = 12 ksi Figure Part A - State of Stress on an Inclined Plane <
The state of stresses at a point of a structure is shown in the figure below.A- find the principal stresses (show the results in a correctly oriented sketch).B- find the maximum shear stress with its average stress (show the results in a correctly oriented sketch).
The state of stress at a point in a structure is shown in the following figure.(a) find the main stresses (Show the results on a sketch ofcorrectly oriented).(b) Find the maximum shear stress with its average stress (Show theresults in a correctly oriented sketch).