Using IRC: 37 - 1984 "Guidelines for the Design of Flexible Pavements" and the following data, choose the total thickness of the pavement. No. of commercial vehicles when construction is completed= 2723 veh/ day Annual growth rate of the traffic = 5.0% Design life of the pavement = 10 years Vehicle damage factor = 2.4 CBR value of the subgrade soil = 5% Data for 5% CBR value No. of Standard Axles, msa 20 25 30 40 Total Thickness, mm 620 640 670 700

Using IRC: 37 - 1984 "Guidelines for the Design of Flexible Pavements" and the following data, choose the total thickness of the pavement. No. of commercial vehicles when construction is completed= 2723 veh/ day Annual growth rate of the traffic = 5.0% Design life of the pavement = 10 years Vehicle damage factor = 2.4 CBR value of the subgrade soil = 5% Data for 5% CBR value No. of Standard Axles, msa 20 25 30 40 Total Thickness, mm 620 640 670 700

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

12. Refer to Figure II-1 attached. A flexible pavement is to be evaluated according to the AASHTO 1972 design guide. The existing pavement has a weighted structural number=3.4, a regional factor=2.0, and a soil support value=4.5. What would be the approximated number of daily equivalent 18-kip axles to be allowed on this road for a 20-year analysis period?a. 10b. 33c. 100d. 1490
The following figure shows concrete pavement with the layer thickness and elastic modulus as indicated. Assume modulus of rupture of 650 psi, load transfer coefficient of 3.2, serviceability loss from 4.5 to 2.5, and drainage coefficient of 0.9. The bedrock depth and loss of support is not considered for the subgrade. Use the design equation or monograph with 50% reliability to solve the following: 1) Determine the number of ESAL that the pavement can carry before failure. 2) If the daily traffic has 1080 single axles (20-kip), 400 single axles (24-kip), and 680 tandem axles (40-kip), and the annul traffic is the same over the design period, how many years would the concrete pavement last before failure? 8-inch Portland Cement Concrete Ec=4×106 psi 8-inch Granular Subbase Ec=30,000 psi Subgrade Mr = 5000 psi
Problem No. 1A flexible pavement for an urban interstate highway is to be designed using the AASHTOmethod to carry a design ESAL of 3 x 106. It is estimated that it takes about a week for water tobe drained from within the pavement and the pavement structure will be exposed to moisturelevels approaching saturation for 30% of the time. The following additional information is available: Elastic modulus of asphalt concrete = 450,000 psiResilient modulus of base material = 35,000 psiResilient modulus of subbase material = 15,000 psiCBR of subgrade material = 8(a) Consider designing the same pavement with only asphalt concrete and base layer (excluding subbase layer). Use the information provided in Problem 1. (b) Compare strengths and weaknesses of each design.
A rigid pavement is designed with an 11-inch slab thickness, 90% Rellability (ZR = -1.282), Es = 4 million psi, modulus of rupture of 600 psi, modulus of subgrade reaction of 150 lb/in?, a 2.8 load transfer coefficient, initial PSI = 4.8, final PSI of 2.5, overall standard deviation of 0.35, and a drainage coefficient of 0.80. The pavement has a 20-year design life. The pavement has three lanes in one direction (PDL = 0.80) and is conservatively designed for trucks that have one 20,000-lb single axle load (1.58), one 26,000-lb tandem axle (0.619), and one 34,000-b triple axle (0.593). What is the daily estimated truck traffic on the three lanes? logia (APSI) S,C¢(D@7% – 1.132) 3.0 [1.62410x10 |(D + 1)*46 | log10 (W) = Zg5, + 7.35 (log,0( D + 1)) – 0.06 +: +(4.22 - 0.327SI) log10 1+ 18.42 215.63/ De75 - 0.25
2. You are asked to design a new flexible pavement structure for an existing road that will be totally replaced. You are provided with the following borehole results: a) Existing (Old) HMA - 135 mm b) Existing (Old) Granular A Base - 170 mm c) Existing (Old) Granular B Subbase - 340 mm d) Gravelly Silty Sand (Till) Subgrade (25 % 5-75 um) What is the current GBE for the existing pavement structure? What is the GBE for the same pavement structure when it was newly constructed?
1. During the AASHO road test, ONLY flexible pavements were constructed and tested.a. Trueb. False2. The AASHO present serviceability rating (PSR) was considered an objective quantity used to establish the performance of highway pavement in terms of applied traffic.a. Trueb. False3. The AASHTO present serviceability index (PSI) correlates the PSR to actual pavement performance in terms of applied traffic, and select distresses.a. Trueb. False4. There is only one AASHTO PSI equation that applies to both flexible and rigid pavements.a. Trueb. False5. The AASHTO PSI scale ranges from:a. 0-5b. 0-10c. 0-100d. None of the above
The elastic modulus of mid-range aggregate asphalt pavement is 480 MPa while its subgrade has an elastic modulus of 55 MPa. What is the stiffness factor of the flexible pavement? 0.12 0.61 0.34 0.49
The overall standard deviation in the flexible pavement design equation accounts for the variation in the loading, materials and the construction practices. O True O False
The AADTT of a 2-way (2-lane each way) highway is 10,000. The directional distribution may vary between 45 and 55% depending on season. The lane distribution may vary between 60 and 75%. The driving lane always carries more loads compared to the passing lane. The growth factor for the pavement is 3.5%. Based on the above information, calculate the design AADTT for the driving lane if the pavement service life is 20 years.
Q#1 What is the primary function of the pavement structure? Why do we use high quality materials as we go from bottom to top of the pavement structure? Discuss various tests used for the quality of bitumen used in flexible pavements. Discuss various tests used for the quality of aggregate used in flexible pavements.
B. A rigid pavement with a 10-inch slab thickness, 90 percent reliability, E. = 4 million lb/in², 600 lb/in² modulus of rupture, 150 lb/in³ modulus of subgrade reaction, a 2.8 load transfer coefficient, initial PSI of 4.8, final PSI of 2.5, overall standard deviation of 0.35, and a drainage coefficient of 0.8 is designed. The pavement's design life is 20 years. The three-lane road is built for vehicles with one 20,000-pound single axle, one 26,000-pound tandem axle, and one 34,000-pound triple axle. Calculate the projected daily truck traffic on the three lanes.
Subject : Transportation Engineering Give me both a and b right solutions A 5 tonne wheel load is applied on a pavement and generates a surface deflection of 0.15 mm. (a) If the equivalent radius of tyre contact is 100 mm and Poisson’s ratio is 0.3, what is the pavement’s modulus of elasticity? (b) If the pavement is 125 mm thick, what is the vertical stress at the top of the subgrade?