Using Stochastic Concept compute the pavement design required for a 9,000lb wheel load and 95 % reliability for a materials that has a mean strength of 600 psi and a standard deviation of 50 psi (for both stress and strength). the rigid pavement thickness, is: Select one: a. 10 IN b. 11 IN O c. 9 IN O d. 12 IN

Using Stochastic Concept compute the pavement design required for a 9,000lb wheel load and 95 % reliability for a materials that has a mean strength of 600 psi and a standard deviation of 50 psi (for both stress and strength). the rigid pavement thickness, is: Select one: a. 10 IN b. 11 IN O c. 9 IN O d. 12 IN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A rigid pavement is to be used to carry a wheel load of 59.35 kN. Enough dowels will be used across the joint. What will be the difference in thickness (in mm) between the edge and the center of the pavement? The allowable tensile strength of concrete is 1.47 MPa. Round off the nearest whole number.
50 KPa is equivalent to: O A) 5x 10^6 N/m^2 O B) 5 x 10^5 N/m^2 O0 5 x 10^3 N/m^2 O D) 5 x 10^4 N/m^2 Concrete is required for a plain concrete pavement to be constructed in Southern Alberta. The pavement will be exposed to freezing, thawing, and deicers. If aggregates with a nominal maximum size of 20 mm are used, what is the minimum cement content per cubic meter of concrete as per the CSA Standard? OA) 320 kg O B) 335 kg OO 390 kg OD) 420 kg During Lab 5, the relative density of a coarse aggregate sample was determined. The sample of coarse aggregate was towel dryed to represent this moisture state: O A) OD B) Wet OC SSD O D) Air Dry When performing the slump test, each layer of concrete is rodded times as per CSA specifications: OA) 20 O B) 25 OO 30 O D) 12
Q5. Given the following information: A concrete pavement for two lane highway has doweled joints and no concrete shoulders. The modulus of subgrade reaction is 200 pci (54.2MN/m3), and the modulus of rupture is 650 psi (4.5Mpa). Assume a load safety factor of 1.1. truck weight distribution data for single axle load is as follows: Axle load(kips) 1 Single axles 28 Multiplied by LSF (1.1) 26 24 2 Expected repetitions 3 Erosion analysis Allowable repetitions 30.8 5,913 28.6 12,483 26.4 15,111 22 24.2 102,492 Using a trial thickness of 8 in. Fill in the empty spaces using PCA design method 4 6. Erosion factor Erosion percent 5
What is the average pavement density if the pavement thickness is 300mm by expansion pressure method. The expansion pressure is 0.150kg/cm².
solve the question given in the image.
Give me the right solution with clear calculations
Q2) A wheel load with circular area has a radius 6 in. and uniform pressure 552 kPa is applied on a two-layer system, consists of asphalt layer has an elastic modulus of 350000 psi and stabilized subgrade has elastic modulus 70000 psi. The subgrade can support a maximum vertical stress allowing for allowable number of stress repetitions of 2.5 x 109 before occurring of permanent deformation. Calculate the required thickness of a full-depth pavement, deflection in pavement and the critical tensile strain at the bottom of asphalt layer.
A transportation agency is planning a pavement roughness data collection program to monitor statewide pavement performance. Assuming that 10 percent of change in roughness should be detectable at 95% confidence level, how many 1-mile pavement segments should be included in the annual condition survey? There are 20,000 center-line miles of pavement in total.
Flexible Pavement Design Assume the thickness of Base Course and Sub Base Course. Compute the SN of Asphalt, Asphalt treated Base, Base course, and Sub base course. Compute the thickness of Asphalt and Asphalt Treated Base.
An undowelled rigid pavement in a subdivision roadway has thickness equivalent to 300mm. What should be the allowable tensile strength of concrete in MPa in order to support a wheel load equivalent to 9kN?
Mechanistic design procedure is based on the assumption that a pavement can be modelled as multi-layered elastic or viscoelastic. Discuss the combination of Visco-elastic considerations assumption in pavement design procedure.
A flexible pavement carries a static wheel load of 53.5kN. The circular contact area of the tire is 85806 square mm and the transmitted load is distributed across a wide area of the subgrade at an angle of 45 degrees. The subgrade bearing value is 0.14MPA, while that of the base is 0.41Mpa. Design the thickness of pavement and that of the base. answer should be in mm. Identity first the thickness of the pavement next the thickness of the base.