A flexible pavement carries a static wheel load of 53.5kN. The circular contact area of the tire is 85806 square mm and the transmitted load is distributed across a wide area of the subgrade at an angle of 45 degrees. The subgrade bearing value is 0.14MPA, while that of the base is 0.41Mpa. Design the thickness of pavement and that of the base. answer should be in mm. Identity first the thickness of the pavement next the thickness of the base.

A flexible pavement carries a static wheel load of 53.5kN. The circular contact area of the tire is 85806 square mm and the transmitted load is distributed across a wide area of the subgrade at an angle of 45 degrees. The subgrade bearing value is 0.14MPA, while that of the base is 0.41Mpa. Design the thickness of pavement and that of the base. answer should be in mm. Identity first the thickness of the pavement next the thickness of the base.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Pls answer w/ complete solution. Asap (Transportation Engineering) Determine the thickness base and subgrade of flexible pavement if the wheel load is 90 kN and has wheel contact area of 88075 sq. mm.. Strength capacity of base is 0.35 MPa and 0.15 MPa for Subgrade.
Show complete solution with clear explanation thanks A rigid pavement is to be used to carry a wheel load of 49KN, the allowable tensile stress of the concrete is 1.4MPa. Sufficient dowels are used across the joints. Design the center of the thickness of the pavement at the center and base
Show complete solution and clear explanation thanks A rigid pavement of the proposed provincial road is to be used to carry a maximum wheel load of 60KN. Neglect the effect of dowels f'c=20MPa. Allowable tensile stress of concrete pavement is 0.6f'c. Calculate the allowable tensile stress of the concrete pavement and thickness of the pavement
07. Determine Structural Number and terminal serviceability index value of flexible pavement. Given B and G, value for 32-kip tandem-axle loads. B= 0,4 G= -0.22
17. In the Asphalt Institute flexible pavement design approach, Where are the critical stress and strain locations checked?a. Top of the asphalt concrete layerb. Middle of the asphalt concrete layerc. Bottom of the asphalt concrete layerd. Bottom of the asphalt concrete layer and top of the subgrade
A pavement consists of 5 inches of asphalt underlain by a crushed stone based course. There is no sub base. The asphalt has an elastic modulus of 350,000 psi at room temperature and the base course has a CBR of 70. Determine the thickness of the crushed stone base needed to reach an SN of 2.85. Assume the base course is saturated 5% of the time and drains within a day.
12. Refer to Figure II-1 attached. A flexible pavement is to be evaluated according to the AASHTO 1972 design guide. The existing pavement has a weighted structural number=3.4, a regional factor=2.0, and a soil support value=4.5. What would be the approximated number of daily equivalent 18-kip axles to be allowed on this road for a 20-year analysis period?a. 10b. 33c. 100d. 1490
An undowelled rigid pavement in a subdivision roadway has thickness equivalent to 300 mm. What should be the allowable tensile strength of concrete in MPa in order to support a wheel load equivalent to 9 kN?
A dual wheel having a load per tire of 4000 Ib, 80 psi pressure and μ = 0.5. Calculate thetotal pavement deflections due to the dual wheel by two layer theory at the followingradial distances from the centerline of one tire: r=0, 7,14. Assume that E1 = 10 E2
A rigid pavement is designed with an 11-inch slab thickness, 90% Rellability (ZR = -1.282), Es = 4 million psi, modulus of rupture of 600 psi, modulus of subgrade reaction of 150 lb/in?, a 2.8 load transfer coefficient, initial PSI = 4.8, final PSI of 2.5, overall standard deviation of 0.35, and a drainage coefficient of 0.80. The pavement has a 20-year design life. The pavement has three lanes in one direction (PDL = 0.80) and is conservatively designed for trucks that have one 20,000-lb single axle load (1.58), one 26,000-lb tandem axle (0.619), and one 34,000-b triple axle (0.593). What is the daily estimated truck traffic on the three lanes? logia (APSI) S,C¢(D@7% – 1.132) 3.0 [1.62410x10 |(D + 1)*46 | log10 (W) = Zg5, + 7.35 (log,0( D + 1)) – 0.06 +: +(4.22 - 0.327SI) log10 1+ 18.42 215.63/ De75 - 0.25
Calculate the equivalent radius of the contact area of tires considering the wheel load is 60 kN.Allowable bearing pressure on the base of the pavement is approximately 0.20 MPa and thethickness of pavement is calculated as 160 mm. Round up the answer in 10 mm interval
B. A rigid pavement with a 10-inch slab thickness, 90 percent reliability, E. = 4 million lb/in², 600 lb/in² modulus of rupture, 150 lb/in³ modulus of subgrade reaction, a 2.8 load transfer coefficient, initial PSI of 4.8, final PSI of 2.5, overall standard deviation of 0.35, and a drainage coefficient of 0.8 is designed. The pavement's design life is 20 years. The three-lane road is built for vehicles with one 20,000-pound single axle, one 26,000-pound tandem axle, and one 34,000-pound triple axle. Calculate the projected daily truck traffic on the three lanes.