Use Housel method to determine the size of square footing required to carry a column load P = 55 tons if the two plate loading tests results are as given below:- Plate size (1) = 30x30 cm, corresponding load= 6.2 tons; relative to 1.0 cm settlement. Plate size (2)=45x45 cm, corresponding load -12 tons; relative to 1.0 cm settlement.

Use Housel method to determine the size of square footing required to carry a column load P = 55 tons if the two plate loading tests results are as given below:- Plate size (1) = 30x30 cm, corresponding load= 6.2 tons; relative to 1.0 cm settlement. Plate size (2)=45x45 cm, corresponding load -12 tons; relative to 1.0 cm settlement.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the elastic settlement using the Schmertmann method of the 10'x 10' footing as shown below. Estimate the elastic modulus using Es = 10(N + 15), where Es is in ksf and N is the corrected SPT value. Loose sand Medium dense sand Loose sand Dense sand Very loose sand DEPTH 5° 10' 15' 20' 25' SPT 10 21 11 15 41 4 Q=250 kips 10' x 10' 0 0.2 0.4 0.6 STRAIN & Layer 1 Layer 2 Layer 3 Layer 4 Laver 5
A 1.70 m by 2.60 m footing has its base 1.70 m below the ground surface. GWT is a meter above its base. (L along x-axis) Y = 15.75 kN/m C= 15 kPa Yut = 19 kN/m =26° Using Meyerhof's formula, determine the net ultimate load that the footing could carry if e = 0.45 m and es = 0.30 m. PLEASE MAKE YOUR HANDWRITING READABLE AND CLEAR. THANK YOU SO MUCH :)
Problem (2.8):The load-settlement data obtained from load test of a square plate of size (1ft) are as shown below. If a square footing of size (7t) settles (0.75 inch), what is the allowable soil pressure of the footing? Consider sandy soil. Load (Tsf) Settlement (inch) 10 0.4 14 0.6 16 0.8 19 1.0 0.1 0.2 0.3
A continuous footing with a B = 7.5ft is constructed with a Df of 3ft in a soil with the following properties: c' = 210 lb/ft? Y = 115 lb/ft³ Ø' = 25° If bedrock exists 6ft below grade use equation 7.2 to determine the ultimate bearing capacity.
2. Change the footing dimension in the question below to a strip footing with width of 6 ft. and find the settlement using Schmertmann's modified method to calculate the required settlement. Example 8-2: A 6 ft x 24 ft footing is founded at a depth of 3 ft below ground elevation with the soil profile and average N160 values shown. Determine the settlement in inches (a) at the end of construction and (b) 1 year after construction. There is no groundwater. The footing is subjected to an applied stress of 2,000 psf. Ground Surface Clayey Silt 3 ft Y = 115 pcf; N160= 8 Sandy Silt B = 6 ft 3 ft Y = 125 pcf; N160= 25 Coarse Sand 5 ft Yt = 120 pcf; N160= 30 Sandy Gravel 25 ft Yt = 128 pcf; N160= 68
b) A 3.X m x 3.X m square foundation is to be founded at a depth of 1.5 m below ground level in medium-dense sand with a bulk unit weight of 19 kN/m³ and a saturated unit weight of 20.X kN/m³. The water table is located 3.6m below ground level. The immediate settlement is to be limited to 25mm. Estimate the allowable load on the foundation using the standard penetration test data presented in Table 3 below and applying the appropriate correction factors. Table 3: SPT results Depth 1.5 3.0 3.8 4.6 5.4 6.4 (m) SPT 7 12 12 18 20 25 'N' X=2 2.2 9
An isolated footing having dimensions of 1.5m x 2.2m is provided at a depth of 1.2m in a stratum of cohesionless soil having a relative density of 71%. Determine the bearing capacity factors Nc, Nq and Nγ as per IS code.
Please round to the nearest One (i.e., 1). No Comma! The results of a plate-load test in a clay soil are shown below. The size of the plate is 0.41m x 0.41m. If a square column foundation (3m x 3m) that should carry a load of 2700KN, what is the estimated settlement of the foundation? Load/unit area Settlement (KN/m²) Load/unit area (kN/m?) (mm) 200 600 800 400 200 300 6. 10 400 13 500 20 20 600 29 30 40 50 60 70 Answer = mm Next page page MacBook Air トII F1 F2 F3 F4 F5 F6 FB F9 @ #3 2$ & 2 3 4 7 8 W R Y U S D F G K Settlement (mm)
The following results were obtained from CU tests on a clay soil that is the foundation material for an embankment. 03 (kPa) 300 400 600 0₁-03 (kPa) 331 420 487 Au (kPa) 111 160 322 (a) Determine the total and effective principal stresses for all three tests (You may summarize them in a table). (b) Recommend the shear strength parameters to be used for short-term and long-term analyses. The maximum confining pressure (cell pressure) at the depth of interest is 300 kPa. (Note: the clay is a normally consolidated one).
Figure (a) shows the cross section of square footing of 3 m x 3 m. The soil properties are shown in the figure. i) ii) Determine the load Q that the footing can carry. Use the factor of safety (FOS) of 2.5. During rainy season, groundwater level increased to the soil surface. Based on this condition, calculate the new FOS and justify whether the existing footing is able to carry the same amount of load as calculated in (a) Not drawn to scale 1.6 m 0.4 m Water level 3m Q Soil properties Yd=18.3K³ Ysat = 21 kN/m³ = 30°
Please round to the nearest One (i.e., 1). No Comma! The results of a plate-load test in a clay soil are shown below. The size of the plate is 0.58m x 0.58m. If a square column foundation (3m x 3m) that should carry a load of 3600KN, what is the estimated settlement of the foundation? Load/unit area Settlement (KN/m²) Load/unit area (kN/m³) (mm) 200 400 600 800 200 6. 300 400 13 10 500 20 20 600 29 30 40 50 60 70 Answer = mm Settlement (mm)
A building will have a factored column load of 300 kN. The column is to be supported on a square spread footing underlain by a soil with the follow properties: c' = 5 kPa, o' 35°, y = 18.5 kN/m³. The groundwater table is at a depth of 15 m and the footing will be located 0.5 m below the ground surface. Determine the required footing size if Þ = 0.5. Use Terzaghi's bearing capacity equation for a square footing. Solve for 'B', making sure to use the reduction factor Þ; trial and error is the easiest way to solve for 'B'. Recommend a "reasonable" dimension for construction/design purposes.