Two equal angles ISA, 100 mm x 100 mm of thickness 10 mm are placed back-to-back and connected to the either side of a gusset plate through a single row of 16 mm diameter rivets in double shear. The effective area of the connected and unconnected legs of each of these angles are 775 mm2 and 950 mm?, respectively. If these angles are not tack riveted, the net effective area of this pair of angles is

Two equal angles ISA, 100 mm x 100 mm of thickness 10 mm are placed back-to-back and connected to the either side of a gusset plate through a single row of 16 mm diameter rivets in double shear. The effective area of the connected and unconnected legs of each of these angles are 775 mm2 and 950 mm?, respectively. If these angles are not tack riveted, the net effective area of this pair of angles is

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

b) Three lona wires, Ctwo bronze and one steel) are equal in lanate and fuppert afe 6715KN at and support mneete rigiel bar o7 iskN ef Comnectedt their bottoms: IF the cross seetion ealeulate a' esch wire is120mm2, of area the stresses in each wire and also the strains in each wire Take F=loukH/mm", Esz200KHlmm²
For the connection shown, the average shear stress in the 12-mm-diameter bolts must be limited to 220 MPa. Determine the maximum load P that may be applied to the connection. O 164 KN 149 kN O 94 KN O 109 kN O 122 kN
DETERMINE THE CENTROIDAL MOMENT OF INERTIA OF THE BUILT-UP SECTION SHOWN USING A STEEL PLATE 1"X16" AND C-12X25 STEEL SECTION WELDED TOGETHER. REFER TO THE TABLLE BELOW FOR THE PROPERTIES 12 Type EDSM Nomenciature AISC Manual Label C15X50 14.7 3.72 3.52 3.40 15.0 8716 0.799 404 11.0 17 C1SK40 C15X40 118 10.0 150 0520 0.400 0510 0650 0.650 0.501 0.501 0.501 0.778 348 315 C15K339 15.0 120 0.788 .07 C1200 C12X25 C12207 C1200 8.01 7.34 3.17 0.674 162 5.12 C1228 C12207 12.0 3.05 234 0.674 144 445 12.0 0.282 129 3.05 1. Determine Ixx (Centroidal) Not in the choices [Select] 1987.6 2. Determine lyy (Centroidal) 1642.67 Not in the choices 1612.7 1752.5
O cd O efgh O ij O klmn O qrst V What is the line of action of which the section will yield in tension? All holes are the same diameter. O aflrsmgb O op t P n j h C d
A bolted connection between a vertical column and adiagonal brace is shown in the figure below. Theconnection consists of three 5/8-in. bolts that join two 1/4-in.end plates welded to the brace and a 5/8-in. gusset platewelded to the column. The compressive load P carried bythe brace equals 8.0k.Determine the following quantities: (a) The averageshear stress τavein the bolts, and (b) the average bearingstress σbbetween the gusset plate and the bolts. (Disregardfriction between the plates.)
x Site: ENGG251 (S122) Mechanics platform.edu.au/mod/quiz/secured.php#lockdown El OC. 0.4 O d. 0.25 x S PowerPoint Presentation X Slide 1 Final exam (Remotely Procto - 6 Updat Question 1.3 A steel bar of rectangular cross section (a = 40 mm, b = 50 mm) carries a tensile load P, as shown in Figure Q1.3. The allowable stress in tension is 100 MPa. The maximum permissible load Pmax is approximately: b n D Figure Q1.3 O a. 50 kN O b. 400 kN O c. 100 KN O d. 200 kN Hide II Proctorio is sharing your screen. Question 1.4 H Stop sharing hp 6 +
Question 1 A da tw M- Determine the section modulus for the below type of I-beam: https://www.engineersedge.com/materials/aisc W.S.M.HP Shapes of- (de)- (det) 11- TH W36X210 61.8 36.7 0.83 12.2 1.36 SH 2.31 2.3125 1.25 32.125 BM T रूम Calculator Section Modulus 1 Beam Un Calculator NA indicates neutral structural shapes/aisc structural shapes viewer.htme Use the information from the above web site link. Enter the value from the table (Sx) in in^3
11-12. A joint is fastened together using two circular bolts. A single plate carries 40 kN load. What is the actual shear stress if the allowable shear stress is 350 MPa and factor of safety is 2.5? A350 Pa CS with 6.5T5MP C. 140 Pa B. A D. 965 MPa Determine the diameter required using the actual shear stress. B. 8.53 mim C. 12.06 mm A. 13.49 mm D. 19.07 mm
ngth of material exam strength of materials exam e/1FAlpQLSe0S4jiBdFukwD10EDn6YcB3b9pFVy9DyHocjzQq4hz4Q1SGw/formResponse GE News Translate For the system shown in Figure, Maximum shear is: * 2 kip 2 kip 2 kip 2 kip -4 ft-4 ft 4 ft-- 4 ft-- -4 ft- 2 kip 4 kip 8 kip O 6 kip For the system shown in Figure. Maximum bending moment is: 90KN
Problem No 2 A flanged-bolt coupling consisting of six 4 inch diameter steel bolts evenly spaced around a bolt circle 12 inches in diameter and four inch diameter aluminum bolts on a concentric circle 8 inches in diameter. What stresses are developed on each bolt of the two bolt-circles when a torque T=75 Kip-in is applied. Use Gs=12 x 10° psi and GA = 4 x10° psi.
Design a clamp coupling to transmit 25 kW at 120 r.p.m. The allowable shear stress for the shaft and key is 50 MPa and the number of bolts connecting the two halves are six. The permissible tensile stress for the bolts is 75 MPa. The coefficient of friction between the muff and the shaft surface may be taken as 0.3.
Six 7/8-in-diameter rivets fasten the plate in Figure below to the fixed member. Determine the average shearing stress caused in each rivet by the 15 kips loads. What additional loads P can be applied before the shearing stress in any rivet exceeds 9100 psi?