ZAO O"l zain IQdocs.google.com/forms O0/10find the tensile stress in upperplate in section 1-151480 kN80 kNQB-bolt DIA. 10 MM80 kN80 kN8-bolt DIA. 10 MM30 MРа33 МРа35 MPа37 MPano one10/10find the tensile stress in upperplate in section 3-3+

Given, P = 80kN Dia if bolt = 10mm Dia of hole = 10 +1 = 11mm No. Of bolts at section 1- 1 = 3,

"l zain IQ A:0 I YA docs.google.com/forms O 0/10 find the tensile stress in upper plate in section 1-1 80 kN 80 kN B-bolt DIA. 1O MM 80 kN 80 kN 8-bolt DIA. 10 MM 30 MРа О 33 МРа 35 MPa 37 MPа no one 300 mm 第 2) 5. -------.

"l zain IQ A:0 I YA docs.google.com/forms O 0/10 find the tensile stress in upper plate in section 1-1 80 kN 80 kN B-bolt DIA. 1O MM 80 kN 80 kN 8-bolt DIA. 10 MM 30 MРа О 33 МРа 35 MPa 37 MPа no one 300 mm 第 2) 5. -------.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter10: Plate Girders

Section: Chapter Questions

Problem 10.5.1P

See similar textbooks

Related questions

Q: How much service live load, in kN/m, can be supported? The member weight is the only dead load. The…

Q: calculation and draw SFD and BMD.

A: Determine the support reaction and draw the shear force and bending moment diagram of the given…

Q: SAMPLE PROBLEMS 1. A force of 800N is exerted on a bolt A as shown. Determine the horizontal and…

A: Step 1: Step 2: Step 3:

Q: REVISED PROBLEM: M3 HW 4 4. Six rivets are used in the connection shown in the figure. If both P= 50…

Q: Problem 4 Determine the design tensile strength Pn of the MC18x58 channel shown based on yielding…

Q: For the clevis connection shown, determine the shear stress in the 20-mm-diameter bolt for an…

Q: :) draw bending moment shear foice and ü) determine the maximum sagging end hogging mom iu)…

A: Fixed end moment MAB=-wL212=-63.43×6.6212=-230.25 KN-mMBA=+wL212=+63.43×6.6212=+230.25…

Q: Find the stress in each rad.

A: Hello dear student, i hope you are doing well & your studies is also going very good. Here im…

Q: A concentrated load of 1500 KN is applied at the ground surface at point A whose coordina (0,0,0).…

A: Solution Using the Boussinesq's Formula σz=3Q2πz2[11+(rz)2]5/2

Q: A bolted connection shown in figure A uses the friction type connection with 22mm diameter A 325…

Q: A joist cutting is used as a bracket to support a load of 135 kN. It is welded to the column flange…

Concept explainers

Properties of materials

A property of a material describes its characteristics and distinguishes it from the others. The material properties are described it in terms of its hardness, color, appearances, and so on. The material properties generally depend on the type of material, or whether it is a metal or an alloy. There are different kinds of material properties such as mechanical properties, thermal properties, physical properties, and chemical properties. Chemical properties describe the material in terms of a chemical change. The mechanical properties come into existence when the material is acted upon by an external load. Thermal properties are associated with the temperature of the material and specific heat.

Question

ZAO O
"l zain IQ
docs.google.com/forms O
0/10
find the tensile stress in upper
plate in section 1-1
5
1
4
80 kN
80 kN
Q
B-bolt DIA. 10 MM
80 kN
80 kN
8-bolt DIA. 10 MM
30 MРа
33 МРа
35 MPа
37 MPa
no one
10/10
find the tensile stress in upper
plate in section 3-3
+

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Compute the nominal shear strength of an M107.5 of A572 Grad 65 steel.
using Figure 5-27, what is the advantage of the suspended type magnet over the other two types of magnets?
A W1422 acts compositely with a 4-inch-thick floor slab whose effective width b is 90 inches. The beams are spaced at 7 feet 6 inches, and the span length is 30 feet. The superimposed loads are as follows: construction load = 20 psf, partition load = 10 psf, weight of ceiling and light fixtures = 5 psf, and live load = 60 psf, A992 steel is used, and fc=4 ksi. Determine whether the flexural strength is adequate. a. Use LRFD. b. Use ASD.
A beam must be designed to the following specifications: Span length = 35 ft Beam spacing = 10 ft 2-in. deck with 3 in. of lightweight concrete fill (wc=115 pcf) for a total depth of t=5 in. Total weight of deck and slab = 51 psf Construction load = 20 psf Partition load = 20 psf Miscellaneous dead load = 10 psf Live load = 80 psf Fy=50 ksi, fc=4 ksi Assume continuous lateral support and use LRFD. a. Design a noncomposite beam. Compute the total deflection (there is no limit to be checked). b. Design a composite beam and specify the size and number of stud anchors required. Assume one stud at each beam location. Compute the maximum total deflection as follows: 1. Use the transformed section. 2. Use the lower-bound moment of inertia.
If the beam in Problem 5.5-9 i5 braced at A, B, and C, compute for the unbr Cb aced length AC (same as Cb for unbraced length CB). Do not include the beam weight in the loading. a. Use the unfactored service loads. b. Use factored loads.
Select an American Standard Channel shape for the following tensile loads: dead load = 54 kips, live load = 80 kips, and wind load = 75 kips. The connection will be with longitudinal welds. Use an estimated shear lag factor of U = 0.85. (In a practical design, once the member was selected and the connection designed, the value of U would be computed and the member design could be revised if necessary.) The length is 17.5 ft. Use Fy=50 ksi and Fu=65 ksi. a. Use LRFD. b. Use ASD.