SITUATION B: The hole pattern for a 25mm x 375mm plate A 50 5050 with standard size holes for M20 bolts is loaded in tension as 10 shown in the figure. A and B represents the edges of the plate, whereas 1, 2, 3, and 4 represents the hole locations. 20 7. Determine the net area for fracture path A-1-2-3-4-B 8. Determine the shear lag factor of the given plate 9. Determine the design strength/capacity for the limit state of yielding and tensile rupture 100 50 001

SITUATION B: The hole pattern for a 25mm x 375mm plate A 50 5050 with standard size holes for M20 bolts is loaded in tension as 10 shown in the figure. A and B represents the edges of the plate, whereas 1, 2, 3, and 4 represents the hole locations. 20 7. Determine the net area for fracture path A-1-2-3-4-B 8. Determine the shear lag factor of the given plate 9. Determine the design strength/capacity for the limit state of yielding and tensile rupture 100 50 001

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

d Given: 9/8 in Diameter of bolt = 7/8 inch Diameter at the root of the thread (bolt) = 0.731 inch Inside diameter of washer = 9/8 inch Tensile stress in the nut = 18 ksi Bearing stress = 800 psi 2 in Required: 5/8 in Shearing stress in the head of the bolt Shearing stress in threads of the bolt Outside diameter of the washer 1 2. 3. 0.731 7/8
Q1 : For the rectangular beam shown in fig. find the following : fy =420 MPa f. = 25 MPa . 1- Bending stresses at the top, bottom and at reinforcement when M=35 kN.m. 2- Bending moment to make initial crack. 3- The bending stresses when the applied bending moment equal to 80 kN. W 340 mm 400 mm 3 Ø 28 300 mm- 6 m-
17. determine the capacity of the details shown below.A992: Fy=50ksi, Fu=65ksiA36: Fy=36ksi, Fu=58ksieffective bolt hole diameter = bolt hole + 1/16"beam properties: tw=0.38 in., bf=7.07 in., tf=0.63 in.Fexx=70ksiq) what is the tensile rupture capacity of flange plate of the flange connection in kips? (2 decimal places)
A 12.5-mm round structural steelrod is loaded in tension to fracture. The 200-mm gagelength of the rod was marked off in 25-mm lengthsbefore loading. After the rod broke, the strain in the50-mm containing the fracture was found to be 0.45mm/mm, and the total elongation of the other 150 mmwas found to be 37.5 mm. Determine the averagestrain for the 200-mm gage length.
A flanged bolt coupling consists of ten 20-mm diameter bolts spaced evenly around a bolt circle 400- mm in diameter. Determine the maximum shear stress formed in 200-mm diameter shaft if the allowable shearing stress in the bolts is 40 MPa. Show complete solution and figure.
Solve 7,8
Problem 3.2 (CE BOARD NOVEMBER 2003, CE BOARD NOVEMBER 2004) The lower ends of the three bars shown are at the same level before the 18 Mg block is attached. Each steel bar has an area of 600 mm 2 and E = 200 GPa. For the bronze rod, the area is 900 mm^2 and E broaze = 83 GPa. Fteel steel Sm a) Find the stress in the bronze rod. b) Calculate the axial stress in the steel rod c) Detemine the elongation of each rod.
Which one of the following is a suitable location for core drilling? O a. column-beam joint O b. mid-portion of a column O c. corners in a shear wall O d. corners in a slab e. mid-span of a beam
2.31 three plates are joined by means of two 3/4-inch bolts, as shown in figure P2.31. Determine the shear stress in each bolt due to a force P = 12klb
Solve 3,4
With the dimensions already given, determine the allowable value of the tensile load P, considering the following parameters (The figure shown below is a hanger): 1. The allowable normal stress at the two vertical bolts (bolts 1 and 2) is 160 MPa. 2. The allowable tensile stress in the hanger (see label) is 110 MPa. 3. The allowable tensile stess in the hanger considering the cross section through the horizontal bolt is 75 MPa. 4. The allowable shear stess at the horizontal bolt is 45 MPa. 5. The allowable bearing stress between the washer and the clip angle at the vertical bolts is 65 MPa. 6. The allowable bearing stress at the "shank" of the horizontal bolt is 180 MPa. 7. The allowable shear stress through the clip angle at the vertical bolts is 35 MPa. Note: Draw the Free Body Diagram, include the proper units and round-off the answers to 3 decimal places.
S = Area of Bearing (in²) 4 4 4 +Tabulated Data and Result Specimen No. 1 2 3 Maximum Load Area of Bearing Maximum Load (lbs.) 20000 20500 21000 Compressive Strength (psi)