An A36 tension plate is 9 mm thick is given below. Bolts are 20 mm. Given that s = 50 mm and g = 75 mm, calculate the net area at tensile fracture line a-b-f-g in mm2. Write your answer rounded to the nearest whole number. 50 | 50 50 g g 50

An A36 tension plate is 9 mm thick is given below. Bolts are 20 mm. Given that s = 50 mm and g = 75 mm, calculate the net area at tensile fracture line a-b-f-g in mm2. Write your answer rounded to the nearest whole number. 50 | 50 50 g g 50

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter3: Tension Members

Section: Chapter Questions

Problem 3.3.8P

See similar textbooks

Related questions

Q: 2. A steel plate is 360 mm wide and 20 mm thick with four bolts hole into the place as shown in the…

A: Answer Given data b= 360 mmt=20 mmNo. of bolts- 4

Q: hected on both legs with 12 mm diameter bolts. Given that s = 50 mm

A: consider figure for solution

Q: An A36 tension plate is 9 mm thick is given below. Bolts are 20 mm. Given that s = 50 mm and g =…

A: Given data in question Thickness of plate Diameter of bolt Bolt lines Guage distance To find out…

Q: A 32-mm rebar with a gauge length of 200 mm was subjected to tension to fracture according to ASTM…

A: Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: In the connection shown, 1/4-in. side and end fillet welds are used to connect the 3-in.-by-1 in.…

Q: An A36 tension plate is 15 mm thick is given below. Bolts are 16 mm. Given that s = 90 mm and g = 70…

Q: The figure shows a plate having a width of 400 mm and thickness of 12 mm is to be connected to…

A: The given figure is shown below:

Q: What force is required to punch a 21-mm-diameter hole in a plate that is 23.8 mm thick? The shear…

Q: diameter of washer = 9/8 inch = stress in the nut 18 ksi g stress 800 psi

A: d=7/8 inch dia of root thread = 0.731 inch din = 9/8 inch tensile stress = 18ksi bearing stress =…

Q: Determine if w12x14 (A36) section is Compact, Non-Compact or slender. Show neat handwriting and…

A: The given data is shown below: W12×14A36 steel

Q: The angle L 8 x 8 x ½ in tension shown in the figure below must resist a service dead load of 35…

Q: A W18×86 beam is riveted tona W24×117 grinder by q connection as shown in the figure. The diameter…

A: Bearing strength is the maximum stress load that the unit can hold before the structure fails. But…

Q: SITUATION 14: A PL 300 x 20 mm is to be connected to two plates of the same material with half the…

Q: With the dimensions already given, determine the allowable value of the tensile load P, considering…

A: Answer (1) Allowable normal stress at the two vertical bolts (1) and 92) is 160 Mpa Allowable…

Q: Determine the design tensile strength of the plate (200 × 100) mm connected to a 12 mm thick…

A: Given: The dimension of the plate is 200 mm x 100 mm. The thickness of plate is gusset is 12 mm. The…

Q: Shear strength value τ = 200 MPa The contents associated with bolts are given. P = 70 kN required…

A: Given, P =70 kNτ = 200 MPa

Q: An A36 tension member shown in the figure is connected with three 19 mm diameter bolts. Dia. Of bolt…

Q: P = 8kN. Using N = 3, determine the allowable stress for A501 grade šteel. dimensions (to 1 decimal…

Q: The minimum thickness of a square base plate with A1= B x N=A2= 600 in2 subjected to Pu = 500 k and…

Q: A 32-mm rebar with a gauge length of 200 mm was subjected to tension to fracture according to ASTM…

A: It is required to determine the stress in the rebar. Here, P is the load and A is the area of the…

Q: Determine if w10x12 (A242) section is Compact, Non-Compact or slender. Show neat handwriting and…

Q: Determine the design tensile strength of plate 150 mm x 12 mm size with holes or 16 mm diameter…

Q: The two wooden boards shown in the figure are connected by a 0.5 in. diameter bolt. Washers are…

Q: A grade 36 round steel bar with a diameter of 0.5 inches and a gauge length of 2 inches was…

A: Hi! Thank you for the question, As per the honor code, we are allowed to answer three sub-parts at a…

Q: s used as a tension member connected on both legs with 20 mm diameter bolts. Given that s = 50 mm,…

A: Given:- 20 mm diameter bolts s = 50 mm t=8mm Ag=1852mm2 To find:- Design strength

Q: The tension member shown in the figure is an A36 steel plate 16 mm thick. The bolts are 22 mm in…

A: To Find :- net area Anet across fracture line a-b-f-g. Given data:- Plate thickness t = 16 mm Bolt…

Q: 2. A steel plate is 360 mm wide and 20 mm thick with four bolts hole into the place as shown in the…

Q: Question 27 An A36 angle bar is used as a tension member connected on both legs with 18 mm diameter…

A: Given:- 12 mm diameter bolts s = 65 mm, Ag = 1852 mm2 t = 8 mm To find:- The design strength (kN)…

Q: s used as a tension member connected on both legs with 22 mm diameter bolts. Given that s = 50 mm,…

A: Given:- Ag = 1,852 mm2 t = 8 mm s = 50 mm, 22 mm diameter bolts To find:- Design strength (kN)

Q: An A36 tension member shown in the figure is connected with three 19 mm diameter bolts. Dia. Of bolt…

Q: Determine if W44x285 (A992) section is Compact, Non-Compact or Slender. Show neat handwriting and…

Q: An A36 tension plate is 10 mm thick is given below. Bolts are 20 mm. Given that s = 65 mm and g =…

A: Given data in question Diameter of bolt Guage distance Bolt lines To find out Net area along the…

Q: +8|-*|*||0| 50|50|-75-1-50-1 'd O 0° 00 OO

Q: gle bar is used as a tension member connected on both legs with 12 mm diameter bolts. Given that s…

A: Given:- 12 mm diameter bolts s = 50 mm, Ag = 1,852 mm2 t = 8 mm To find:- design strength (kN)

Q: An A36 tension plate is 11 mm thick is given below. Bolts are 20 mm. Given that s = 60 mm and g =…

A: Given data in question Diameter of bolt Guage distance Thickness of plate To find out Net area of…

Concept explainers

Connections

In steel structures, connections are the members that join two or more steel members. The connections are the most important members of any steel structure, and hence, they are designed more carefully. The majority of the construction cost of steel structures is incurred due to the connections. The design of connections is done as per the recommendations and specifications of the American Institute of Steel Construction (AISC).

Question

An A36 tension plate is 9 mm thick is given below. Bolts are 20 mm. Given that s = 50 mm and g = 75 mm, calculate the net area at tensile fracture line a-b-f-g in mm2. Write
your answer rounded to the nearest whole number.
50
50
+ S + S >
d
a
50
g
50

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

An A36 tension plate is 10 mm thick is given below. Bolts are 20 mm. Given that s = 65 mm and g = 70 mm, calculate the net area at tensile fracture line d-e-b-f-g in mm2. Write your answer rounded to the nearest whole number.
An A36 tension plate is 15 mm thick is given below. Bolts are 16 mm. Given that s = 90 mm and g = 70 mm, calculate the net area at tensile fracture line d-e-b-c in mm2. Write your answer rounded to the nearest whole number. 50 | 50 +S +S 50 g 50
An A36 tension plate is 11 mm thick is given below. Bolts are 20 mm. Given that s = 60 mm and g = 70 mm, calculate the net area at tensile fracture line d-e-b-c in mm2. Write your answer rounded to the nearest whole number.
Determine the design tensile strength of the plate (200 × 100) mm connected to a 12 mm thick gussets, using 20 mm bolts shown below, if the yield and ultimate stress of the steel used are 250 MPa and 420 MPa respectively, fy= 250 MPa fu= 450 MPa
An A36 tension member shown in the figure is connected with three 19 mm diamter bolts. Diameter of hole = 22mm. Properties of 150 mm x 100 mm x 12.5 mm angle A = 3065 mm2 y = 50.55 mm Fy = 248 MPa Fu = 400 MPa Determine the desire strength due to fracture in the net section. Use U = 0.85 kN
2. A steel plate is 360 mm wide and 20 mm thick with four bolts hole into the place as shown in the figure. Compute the following: a. Critical net area required by the NSCP specs. b. Max. critical net area required by the NSP specs. Note that, Max. net area is 85% of the critical net area Capacity of the joint if the allowable tensile stress is 0.75Fy. Use A36 steel Fy=248 MPa 25 mm= DIAMETER OF BOLTS 45 45mm fmmy C. 90mm 90mm 90mm Comm P
An A36 tension member shown in the figure is connected with three 19 mm diameter bolts. Dia. Of bolt hole = 22 mm. %3D 50, 100 100 99.45 T- 50.55 100 Properties of 150 mm x 100 mm x 12.5 mm angle A = 3065 mm? y = 50.55 mm Fy = 248 MPa Fu = 400 MPa Determine the design strength due to fracture in the net section. UseU 0.85. (kN)
Subject: Steel design- Bolted Steel Connection *Use NSCP 2015 formula/guide to solve this problem *Use Handwritten
Determine the allowable strength of the figure as shown
2. A steel plate is 360 mm wide and 20 mm thick with four bolts hole into the place as shown in the figure. Compute the following: a. Critical net area required by the NSCP specs. b. Max. critical net area required by the NSP specs. Note that, Max. net area is 85% of the critical net area c. Capacity of the joint if the allowable tensile stress is 0.75Fy. Use A36 steel Fy=248 MPa 90m²m 90 mm 90mm 45 45mm In my comin P Scanned with CamScanner CS
The given angle bar L125x75x12 with Ag = 2,269 sq.mm. is connected to a gusset plate using 20 mm diameter bolts as shown in the figure. Using A36 steel with Fy = 248 MPa and Fu = 400 MPa, determine the following: 2. Determine the nominal tensile strength of the 12 mm thick, A36 angle bar shown based on: a. Gross yielding b. Tensile rupture Bolts used for the connection are 20 mm in diameter. O O O O O O O Effective net area of the tension member if the shear lag factor is 0.80. Select the correct response: 1,516.1 1,354.4 1,431.2 1,221.6
SITUATION 14: A PL 300 x 20 mm is to be connected to two plates of the same material with half the thickness by 25 mm Ø rivets as shown in the figure. The rivet holes have a diameter 2 mm larger than the rivet diameter. The plate is A36 steel with Fy= 250 MPa, allowable tensile stress of 0.60Fy and allowable bearing stress of 1.35Fy. The rivets are A502, Grade 2, hotdriven rivets with allowable shear stress of 150 MPa. 25 mm Ø rivets + + PL 300x20 P/2 P P/2 PL 300x10 43. Which of the following most nearly gives the max. load in kN that can be applied to the connection without exceeding the allowable shear stress in the rivets? a. 675 KN b. 490 KN c. 598 KN d. 790.5 kN 44. Which of the following most nearly gives the max. load in kN that can be applied to the connection without exceeding the allowable bearing stress between the plates and the rivets? a. 490 KN b. 675 KN c. 598 KN d. 790.5 kN 45. Which of the following most nearly gives the max. load in kN that can be applied to the…