Two designs for a beam are to be considered. Determine which one will support the loading shown below without exceeding the allowable bending stress of 250 MPa in tension and compression and the allowable shear stress of 145 MPa? Your final answer should be section A, section B, either section, or neither section. 25 kN/m 20 kN/m 10 kN/m A 4 m AV 4 m B 50 kN m 4 m 4 m

Two designs for a beam are to be considered. Determine which one will support the loading shown below without exceeding the allowable bending stress of 250 MPa in tension and compression and the allowable shear stress of 145 MPa? Your final answer should be section A, section B, either section, or neither section. 25 kN/m 20 kN/m 10 kN/m A 4 m AV 4 m B 50 kN m 4 m 4 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Consider the figure below, depicting a simple beam AB supporting two equal concentrated loads P. *Inserted Photo* (Use the deformation sign convention. When entering expressions, use the following as necessary: P, L, and a.)
The timber member has a cross-sectional area of 1700 mm2 and its modulus of elasticity is 12 GPa. Compute the change in the total length of the member after the loads shown are applied. A 40 KN B. 1.5 m- 3 m 35 kN C + 3 m D 20 kN
urses MIME3 130 / 10. SECTION ASSESSMENTS Homework - Semester AY 2020 - 2021 Moving Forward A beam has a bending moment of 2 kN-m applied to a section with a hollow circular cross-section of external diameter 3.9 cm and internal diameter 2 cm. The modulus of elasticity for the material is 210 x 10° N/m2. Calculate the radius of curvature and maximum bending stress. Also, calculate the stress at the point at 0.8 cm from the neutral axis Solution: (i) The moment of inertia = ii) The radius of curvature is (iii) The maximum bending stress is iv) The bending stress at the point 0.8 cm from the neutral axis is
You are designing a floor beam in an office building that must support a factored bending moment of M, Ed = 602.1 kNm Assume that the beam is Section Class 1, fully restrained and has a yield strength of 355 N/mm2 Based on stress, what is the minimum plastic section modulus that should be chosen? Give your answer in cm and to the nearest whole number. Do not put units in the answer box.
1. Design the tension member given below. Consider all possible failure modes and prevent sagging. Find the design tension forces for both LRFD and ASD concepts. Determine the Lmax. 5355 is the material. 4 7.5 4 0 0 0 5 10 10 Units are in cm IPN 400 (1400 in table) M20 with standart holes Lmax =? 0 0 0 10 10 5 4 7.5 4
View Policies Current Attempt in Progress A steel [E = 200 GPa] rod with a circular cross section is 18 m long. Determine the minimum diameter required if the rod must transmit a tensile force of 340 kN without exceeding an allowable stress of 200 MPa or stretching more than 14 mm. drod i mm
PROBLEM 3 340 mm The plates are connected by 9-20 mm bolts. Force F = 5Ở KN are applied at both plates in opposite directions as shown in Figure 3. Compute the following: A. Axial stress of each plate. B. Shear stress of each bolt. Assume that each bolt resists the applied force equally. %3D +F 150 mm 中 F 50 mm 340 mm Figure 3: Bolted Plates
An SSTM A36 strucural steel beam 3.6 m long is placed between two rigid supports when the temperature is 15 0C. What is the stress developed in the beam if the temperature rises to 50 0C? ___ MPa. Assume that the proportional limit is 235 MPa, and that lateral buckling is prevented. Calculate your answer to 1 decimal place.
STRENGTH OF MATERIALS (Please write the complete solutions and FBDs completetely and correctly. No long explanation needed.Thumbs up will be given) A loaded beam, 60 mm wide by 200 mm high and 8 in long, has the shear and moment diagrams as shown below. (a) Determine the magnitude, type and location of the maximum flexural stress (b) Determine the type and magnitude of stress in a fiber 40 mm from the top of the beam at a section 2.5 m from the left end, Express final answers in MPa. (Use I=bh3/12)
If the load that can be supported by the given support structure is unknown, calculate the maximum load that the structure can support by considering the maximum allowable stress for section BC is 155.8 MPa. provide your answer in kN with precision to two decimal points. 600 mm Answer: 50 mm d-20 mm 800 mm- B
A simply supported steel beam is loaded with a uniformly distributed load and a torque. The beam has a U-shaped cross section, as shown. Determine the maximum normal compressive and tensile stresses caused by the acting loads. Express your answer in kgf/cm2 and in MPa.
A rectangular steel block is 3.0 inches long in the x-direction, 3.0 inches long in the y-direction, and 4.5 inches long in the z-direction. The block is subjected to a tri-axial loading of three uniformly distributed forces as follows: 50 kips tension in the x-direction, 60 kips compression in the y-direction, and 54 kips tension in the z-direction. If Poisson's ratio is 0.30 and E = 29 x 106 psi, find the uniformly distributed load that must be added in the x-direction to produced no deformation in the z-direction. Your final answer should include two decimal places