A rectangular steel block is 4 inches long in the x direction, 2.5 inches long in the y direction, and 6 inches long in the z direction. The block is subjected to a triaxial loading of three uniformly distributed forces as follows: 50 kips tension in the x direction, 60 kips compression in the y direction, and 55 kips tension in the z direction. If v = 0.30 and E = 29 x 106 psi, determine the single uniformly distributed load in the x direction that would produce the same deformation in the y direction as the original loading.

A rectangular steel block is 4 inches long in the x direction, 2.5 inches long in the y direction, and 6 inches long in the z direction. The block is subjected to a triaxial loading of three uniformly distributed forces as follows: 50 kips tension in the x direction, 60 kips compression in the y direction, and 55 kips tension in the z direction. If v = 0.30 and E = 29 x 106 psi, determine the single uniformly distributed load in the x direction that would produce the same deformation in the y direction as the original loading.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: When solving the problems for Section 1.6, assume that the material behaves linearly elastically.…

A: Given data in question Diameter Elasticity modulus Poissons ratio To find out Largest force P

Q: hollow cast iron column with the cross section shown in the image attached is subjected ti a…

A: A vertical point load acting at A of magnitude 100kNTo determine the maximum compressive and tensile…

Q: As shown below a rectangular R.C.C. column is subjected to compressive force P at an eccentricity of…

A: Given : fy =250 MPa E = 200000 MPa NA depth = 360 mm M20 concrete

Q: 7. A solid aluminum cylinder is placed within an ASTM A501 steel tube as shown. Compute the stresses…

A: Given Data: The diameter of the solid aluminum cylinder is d1=3 in. The diameter of the steel tube…

Q: Challenge Problem 6: A 3/4 in. diameter punch is used to punch a hole through a steel plate 1/2 in.…

A: Given Load 60,000 lbDiameter 3/4 inThickness 1/2 inTo find out Shear stress

Q: The wood beam has an allowable shear stress of Tallow 3.5 MPa. 50 mm 4 Part A 200 mm 50 mm 4 50 mm +…

A: Given:Allowable shear stress = 3.5 MPaRequired:Maximum shear force V

Q: efine the terms shear stress and shear strain, illustrating your answer by means of a simple sketch.…

A: Given data: Shear load 30 kN Shear stress in brass⩽50 MPa Shear stress in steel⩽100 MPa

Q: THE PLATE SHOWN IN THE FIGURE IS FASTENED TO THE FIXED ΜΕMBER BY FIVE 10- MM- DIAΜΕ TER RIVETS.…

Q: determine the minimum force P required to punch the slot. Punch O 575 kN O 675 kN O 724 KN Slug…

Q: 11.18 A long, flat steel bar 4 in. wide and 3 in. thick is reduced in width to 3 in. There are…

A: Applied load (P)=12000lb D=4in d=3 in Thickness (t)=3/8 in

Q: A rectangular steel block is 4 inches long in the x direction, 2 inches long in the y direction, and…

A: As per company policy, we are supposed to answer the first three sub-divisions. Repost the question…

Q: A steel pod is between two rigid walls and carries a tensile load of 6000N at c. If the allowable…

A: The given data is: Tensile load, T=6000 N (At 24° C) Allowable load<130 MPa (At 24° C)…

Q: Consider the T-beam shown in (Figure 1). Take wy 18 kN/m and toy-27 kN/m Figure 200 mm C 200 mm 20…

Q: Part A If the bolt is subjected to a compressive force of P = 21.9 kN, determine the magnitude of…

A: Length of bronze and steel rod is same.The change in length of steel is equal to the change in…

Q: Problem 3- The shown aluminum block with a rectangular cross section in subjected to a compressive…

A: If you have any doubts please comment

Question

A rectangular steel block is 4 inches long in the x direction, 2.5 inches long in the y direction, and 6
inches long in the z direction. The block is subjected to a triaxial loading of three uniformly distributed
forces as follows: 50 kips tension in the x direction, 60 kips compression in the y direction, and 55
kips tension in the z direction. If v = 0.30 and E = 29 × 106 psi, determine the single uniformly
distributed load in the x direction that would produce the same deformation in the y direction as the
original loading.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Question 4 : Please answer part A and B!
Quiz1
A high-strength steel bar used in a large crane has a diameter d = 3.00 in. (see figure). Ⓡ The steel has a modulus of elasticity E = 29 x 105 psi and Poisson's ratio is y = 0.27. Because of clearance requirements, the diameter of the bar is limited to 3.002 in. when it is compressed by axial forces. What is the largest compressive load Pmax that i permitted? Assume that the material behaves linearly elastically. (Enter the magnitude in lb.) lb
Show step by step solution
Problem 6: The compound bar containing steel, bronze, and aluminum segments carries the axia! loads shown in the figure. The properties of the segments and the working stresses are listed in the table. Steel 2 ft Bronze 4 ft A (in.²) E (psi) o, (psi) Aluminum 3 ft 2P Steel 0.75 30 × 106 20 000 Bronze 1.00 12 x 106 18 000 4P Aluminum 0.50 10 x 106 12 000 Determine the maximum allowable value of P if the change in length of the entire bar is limited to 0.08 in. and the working stresses are not to be exceeded.
A3-m long steel plate having a cross-section of 25 mm x 300 mm is used as a hanger and subjected to a tensile load of 1070 KN. Poisson's Ratio = 0.25 and E = 200 000 MPa. Compute the total lateral deformation in mm (along the 300 mm side). Express your answers in 4 decimal places.
A rectangular steel bar with given dimensions is subjected to a axial compression. What is the critical buckling load? width, b = 42 mm thick, t = 60 mm L = 3.25 E = 180 Gpa
A rectangular plate is subjected to uniform biaxial stress with x = 90 MPa (tension), oy = -20 MPa (compression), and ₂ = 0. The plate has original dimensions 400 X 800 X 200 mm (x X y X z) and is made of steel with E = 200 GPa and v = 0.3. What are the strains Ex, Ey, and Ez?
A composite shaft is made by slipping a bronze tube of 3.8-in. outer diameter and 2.5-in. inner diameter over a solid steel shaft of the same length and 2.5-in. diameter. The two components are then fastened rigidly together at their ends. What is the largest torque that can be carried by the composite shaft if the working shear stresses are 10 ksi for bronze and 14 ksi for the steel? For bronze, G = 6 x 10⁰ psi, and for steel, G = 12 x 10° psi.