Challenge Problem 6: A 3/4 in. diameter punch is used to punch a hole through a steel plate 1/2 in. thick. The force necessary to drive the punch through the plate is 60,000 lb. Compute the shear stress developed in the plate. (Hint: How does a punch remove material? What is the area sliding in this failure?)

Challenge Problem 6: A 3/4 in. diameter punch is used to punch a hole through a steel plate 1/2 in. thick. The force necessary to drive the punch through the plate is 60,000 lb. Compute the shear stress developed in the plate. (Hint: How does a punch remove material? What is the area sliding in this failure?)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 4) Explain and illustrate variations of normal stresses everywhere on the bar and state why it is…

A: Given: A bar carrying tensile load and having two holes on the bar. Tensile load=P Due to this load,…

Q: A 2 in. diameter puncher is used to punch a hole through a steel plate 1/2 in. thick. The force…

A: Given data, Force P = 45000 lb = 45 kip Diameter of hole D = 2 inch Plate thickness t = 0.5 inch To…

Q: 2. A metal plate is .125 inch thick. What force is required to punch out a square piece 1" x 1"? Th…

A: Thickness of metal plate is 0.125 inch Size of square piece is 1''×1'' The ultimate shear stress of…

Q: 18,000 lbs K₁ 3) This steel bar is 3" x 3" by 30" long. It has a 1" diameter hole centered in the…

Q: An 8 inch ID steel pipe with a 3/8 inch wall thickness has an allowable stress of 25000 psi. What is…

A: The objective of the problem is to determine the maximum allowable pressure of a fluid within a…

Q: A rectangular hole 5 mm × 15 mm is punched in a 2.0 mm thick steel plate of by a load of 100 kN.

Q: Answer fast and explain the answer

Q: A hollow cylinder with an OD of 100mm and an ID of 30mm, supports a load of 100kN. What is the…

Q: Steel tape used in a tape measure has a thickness of 0.0065 in. If the allowable stress is 68 ksi,…

Q: The maximum safe compressive stress in a hardened steel punch is limited to 0.8 GPa and the punch is…

A: The given data is: Maximum safe compressive stress=0.8 GPa=800 MPa The shearing stress of plate=300…

Q: efine the terms shear stress and shear strain, illustrating your answer by means of a simple sketch.…

A: Given data: Shear load 30 kN Shear stress in brass⩽50 MPa Shear stress in steel⩽100 MPa

Q: A hole is to be punched through a steel plate of 8 mm thickness. What is the least diameter of hole…

A: given steel plate thickness=8 mmcompressive stress=800 N/mm2ultimate shear strength=300 N/mm2

Concept explainers

Design criteria for structural loading

The different loads such as loads due to self-weight (dead load) and external loads such as live load, wind loads, seismic load, snow load, and other loads and load combinations that influence the design of a building are called structural loading. The nature of the applied load differs from changes in the location, design, and type of materials used. The design criteria require that structures must be designed and constructed to be able to withstand all load types that are expected to act upon the structure and render its usage for the designated purpose. The structural members such as beams, slabs, columns, and foundations help the structure to withstand the applied load. There are different institutes such as ASCE and ACI that provide building design codes to assure minimum safety requirements and quality of the structures.

Question

Challenge Problem 6: A 3/4 in. diameter punch is used to punch a hole through a steel plate 1/2 in. thick. The force
necessary to drive the punch through the plate is 60,000 lb. Compute the shear stress developed in the plate. (Hint:
How does a punch remove material? What is the area sliding in this failure?)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: State of given data

VIEW

Step 2: Shear stress calculation

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Show neat and complete solution
Help me answer pls. Thank you.
11.18 A long, flat steel bar 4 in. wide and 3 in. thick is reduced in width to 3 in. There are circular fillets of in. radius on each side. If the bar is subjected to an axial tensile load of 12,000 lb, calculate (a) the average tensile stress in the wide portion of the bar some distance from the change in section. (b) the average tensile stress in the narrow part of the bar. (c) the maximum tensile stress adjacent to the circular wild fillet. 11 10 A long flat steel bar 5 in wide and in thick has a circu 162111 3 H ar 11.28 A P (a (E
Please provide all necessary information, explanation, and solutions. Thank you!
Describe suction in stress path analysis.
A 42 meter solid shaft is under torsional loading 53 Nm. If in this application, the allowable shear stress for the material is 369 MPa. Calculate the required minimum diameter of the shaft: _____ mm ( input the value directly from your calculation before rounding it up to an engineering accepted diameter) Pay attention to units, and calculate your answer to one decimal place.
The shaft is made of L2 tool steel, has a diameter of 40 mm, and is fixed at its ends A and B. It is subjected to the couple shown where F = 2.8 kN. (Figure 1) Figure 400 mm 600 mm 50 mm 50 mm 1 of 1 Determine the maximum shear stress in region AC. Express your answer to three significant figures and include appropriate units. (TAC)max = 61.1 μA Submit Previous Answers Request Answer Part B X Incorrect; Try Again; 9 attempts remaining (TCB)max = MPa Determine the maximum shear stress in region CB. Express your answer to three significant figures and include appropriate units. μA Value ? Units ?
An SSTM A36 strucural steel beam 3.6 m long is placed between two rigid supports when the temperature is 15 0C. What is the stress developed in the beam if the temperature rises to 50 0C? ___ MPa. Assume that the proportional limit is 235 MPa, and that lateral buckling is prevented. Calculate your answer to 1 decimal place.
A circular hole is to be punched in a plate that has a shear strength of 40 ksi. The working compressive stress for the punch is 50 ksi. Determine: a) The maximum thickness in inches of a plate in which a hole 2.5 in. in diameter can be punched. b) If the plate is 0.25 in. thick, determine the diameter in inches of the smallest hole that can be punched. Note: Draw the Free Body Diagram, include the units/dimensions, use the proper formula and round-off all the answers and final answers to 3 decimal places.
Can I get a walkthrough for this problem?
please solve the following problem on pencil and paper so I can understand. Please show all work.