Can I get a walkthrough for this problem? Given the stress-strain relationship for an aluminum alloy specimen, choose thecorrect (nearest) Young's modulus within the linear portion and tangent modulus at astress of 45,000 psi.60,00012/40,0000.002 0.004 0.006Strain, in./in.Oe.Young's modulus = 4.8x10^6 psi; Tangent modulus = 10x10^6 psiYoung's modulus = 10x10^6 psi; Tangent modulus = 4.7×10^6 ksiYoung's modulus = 5x10^6 psi; Tangent modulus = 4.7x10^6 psiYoung's modulus = 10x10^6 psi; Tangent modulus = 4.7x10^6 psi

Provided data,Stress =45000 psi

Given the stress-strain relationship for an aluminum alloy specimen, choose the correct (nearest) Young's modulus within the linear portion and tangent modulus at a stress of 45,000 psi. Stress, psi 60,000 40,000 20,000 0 0 0.002 0.004 0.006 Strain, in. /in. 0.008 Young's modulus = 4.8x10^6 psi; Tangent modulus = 10x10^6 psi Young's modulus = 10x10^6 psi; Tangent modulus = 4.7x10^6 ksi Young's modulus = 5x10^6 psi; Tangent modulus= 4.7x10^6 psi Young's modulus = 10x10^6 psi; Tangent modulus = 4.7x10^6 psi

Given the stress-strain relationship for an aluminum alloy specimen, choose the correct (nearest) Young's modulus within the linear portion and tangent modulus at a stress of 45,000 psi. Stress, psi 60,000 40,000 20,000 0 0 0.002 0.004 0.006 Strain, in. /in. 0.008 Young's modulus = 4.8x10^6 psi; Tangent modulus = 10x10^6 psi Young's modulus = 10x10^6 psi; Tangent modulus = 4.7x10^6 ksi Young's modulus = 5x10^6 psi; Tangent modulus= 4.7x10^6 psi Young's modulus = 10x10^6 psi; Tangent modulus = 4.7x10^6 psi

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.5P: The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen...

See similar textbooks

Related questions

Q: Upon being engaged to provide resident inspection on a project, what kind of documents are needed by…

A: The inspection on a project is carried out systematically and in accordance with the details given…

Q: The expected finishing date for the project with 85% probability. * Actv. Duration (month) a m b…

Q: Explain the following term 1.2 Taking off

A: Let us understand the term taking off in step 2.

Q: Please make a PERT CPM use the activity and duration below. Also use the format stated. PLEASE DON'T…

A: I will create a PERT CPM (Program Evaluation Review Technique Critical Path Method) chart using the…

Q: Activity List for a Reroofing Project Activity Description 1 Mobilize 2 Set up scaffolding 3…

Q: Who is responsible for developing an inspection plan?

A: Inspection of any sort of work is an important parameter for ensuring its safety, performance and…

Q: How is the beneficial occupancy used?

A: Beneficial occupancy or “beneficial occupation” is a term that can be used to describe a building…

Q: Given the building layout for Store A, Store B, Store C, and Store D, what portion of the shared…

A: Given: Total maintenance cost = $7500 Area of store A = Area of store D = 2500 ft2 Area of store B =…

Q: . How much testing is performed by the Resident Project Representative and his staff?

A: The Resident Project Representative is a person assigned to a particular project on a full-time…

Question

Can I get a walkthrough for this problem?

Given the stress-strain relationship for an aluminum alloy specimen, choose the
correct (nearest) Young's modulus within the linear portion and tangent modulus at a
stress of 45,000 psi.
60,000
12/
40,000
0.002 0.004 0.006
Strain, in./in.
Oe.
Young's modulus = 4.8x10^6 psi; Tangent modulus = 10x10^6 psi
Young's modulus = 10x10^6 psi; Tangent modulus = 4.7×10^6 ksi
Young's modulus = 5x10^6 psi; Tangent modulus = 4.7x10^6 psi
Young's modulus = 10x10^6 psi; Tangent modulus = 4.7x10^6 psi

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data

VIEW

Step 2: Starin based on stress given

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
A tensile test was performed on a metal specimen with a diameter of 1 2 inch and a gage length (the length over which the elongation is measured) of 4 inches. The dam were plotted on a load-displacement graph. P vs. L. A best-fit line was drawn through the points, and the slope of the straight-line portion was calculated to be P/L =1392 kips/in. What is the modulus of elasticity?
A tensile test was performed on a metal specimen having a circular cross section with a diameter of 1 2 inch. The gage length (the length over which the elongation is measured) is 2 inches. For a load 13.5 kips, the elongation was 4.6610 3 inches. If the load is assumed to be within the linear elastic rang: of the material, determine the modulus of elasticity.
The stainless steel specimen is shown in Figure 3 with tensile engineering stress-strain behaviour. a)Compute the modulus of elasticity. and Compute the yield strength at a strain offset of 0.002.
a13 both
3. The distribution of stress in an aluminum machine component is given (in megapascals) by Ox = y + z? Oy = x + z Oz = 3x + y Txy = 3z2 Tyz = x Txz = %3D Calculate the state of strain at a point positioned at (1,2,4). Use E=70 GPa and v = 0.3
Data taken from a stress-strain test for a brittle alloy are given in the table. The curve is linear between the origin and the first point. o (ksi) e (in./in.) 0 0 44.8 0.0008 54.0 0.0013 57.5 0.0017 59.5 0.0021 60.0 0.0023 Part A Determine approximately the modulus of toughness. The rupture stress is o, 30.0 ksi. Express your answer in inch-pounds per cubic inch as an integer. VAE Ivec U Submit Provide Feedback Request Answer in-lb/in³
1.14 The stress-strain relation shown in Figure P1.14 was obtained during the ten- sile test of an aluminum alloy specimen. 60,000 40,000 20,000 0.002 0.004 0.006 0.008 Strain, in./in. FIGURE P1.14 Determine the following: a. Young's modulus within the linear portion b. Tangent modulus at a stress of 45,000 psi c. Yield stress using an offset of 0.002 strain d. If the yield stress in part c is considered failure stress, what is the maximum working stress to be applied to this material if a factor of safety of 1.5 is used? Stress, psi
A test conducted on a steel bar whose cross section is 0.5 in. by 4 in. is performed. Anaxial load of P = 30,500 lb. produced a deformation of 0.00103 in. over a gauge lengthof 2 in. and a decrease of 0.000078 in. in the 0.5-in. thickness of the bar. Determinea. Poisson’s ratio,b. the elastic modulusc. the decrease in the 4-in. cross-sectional dimension.
The stress–strain relationship shown in Figure was obtained during the tensile test of an aluminum alloy specimen. Determine the following:a. Young’s modulus within the linear portionb. Tangent modulus at a stress of 45,000 psic. Yield stress using an offset of 0.002 straind. If the yield stress in part c is considered failure stress, what is the maximum working stress to be applied to this material if a factor of safety of 1.5 is used?
Please answer letters a, b, c and d. Thank you!