Problem 6:The compound bar containing steel, bronze, and aluminum segments carriesthe axia! loads shown in the figure. The properties of the segments and the workingstresses are listed in the table.Steel2 ftBronze4 ftA (in.²)E (psi)o, (psi)Aluminum3 ft2PSteel0.7530 × 10620 000Bronze1.0012 x 10618 0004PAluminum0.5010 x 10612 000Determine the maximum allowable value of P if the change in length of the entirebar is limited to 0.08 in. and the working stresses are not to be exceeded.

Answered: Image /qna-images/answer/db39f124-c52e-4e1a-a8c5-e187d85df278.jpg

Answered: Problem 6: The compound bar containing…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Description A1 m long steel rod has a cross sectional area of 100 sqm. It is Elasticity modulus is 200 000 MPa. 1. Determine deformation of steel rod. 2. Determine stiffness of steel rod. 3. Determine flexibility of steel rod.
In the figure below, a joint is made by gluing two plywood gussets of thickness t to wood boards. The tensile working stresses are 1245psi for the plywood and 725psi for the boards. The working shear stress for the glue is 52psi. Determine the dimension b so that the joint is as strong as the boards.____________inches in 2 decimal places.
Getting measurements from Figure , determine approximate values of the following items for steel with different carbon contents. Use one system of units only as specified by the instructor.a. Yield stressb. Ultimate strengthc. Strain at failured. Effect on modulus of elasticitye. Approximate toughness. Curves may be approximated with a series of straight lines.f. Comment on the effect of increasing carbon content on items a through e above.
Determine the compressive force (in lb) in the bars shown after a temperature rise of 173°F if d = 0.015 in. Round off the final answer to five decimal places. Use the following data: Bronze Aluminum A = 2.24 sq. in A = 2.78 sq. in E = 14959726 psi E = 10594540 psi L = 12.5 in L = 16.6 in α = 11.61 x 10-6/ °F α = 12.67 x 10-6/°F
PROBLEM 01: Hollow bar length is 1.40m long and tube length is three-fourth as long as the bar. Torque T=1100N.m acts at the free end of the bar. Both the bar and tube are made of an aluminum alloy with shear modulus of w ww elasticity G=27GN/m². Given that dl=35mm, d2=45mm, d3=60mm, d4=70mm. Determine the following: a. Maximum shear stress in both the bar and tube b. Angle of twist at the end A of the bar. (In degrees) Tube Fixed plate End plate Tube d3 d1 d2 d4 Bar Cross-section of the bar and tube
The pin-connected structure shown in the figure consists of a rigid beam ABCD and two supporting bars. Bar (1) is a bronze alloy [E = 94 GPa] with a cross-sectional area of A₁ = 280 mm2. Bar (2) is an aluminum alloy [E = 71 GPa] with a cross-sectional area of A2 = 590 mm². All bars are unstressed before the load P is applied; however, there is a 3-mm clearance in the pin connection at A. Assume L₁ = 1840 mm, a = 880 mm, b = 540 mm, c = 430 mm, and L₂ = 1340 mm. If a load of P = 87 kN is applied at B, determine (a) the normal stresses in both bars (1) and (2). (b) the downward deflection of point A on the rigid bar. h (1) L₁ b a BI Answers: C (2) D L2
Two T-shape sections are welded together to create a composite l-beam section as shown below. Determine the safely uniform load w (kN/m) that the beam can carry throughout its entire span. 270mm 30mm 20mm 160mm Welded Joint 130mm 30mm 135mm Beam Length = 4 m Consider the following stresses: fb(T) 3 125 МPа fb(C) = 130 MPa x at the welded joint = 20 MPa Find: 1. The Neutral Axis from the base 2. moment of inertia with respect to the horizontal centroidal axis 3. Q at the welded joint 4. Considering the maximum flexural stress in tension, WNAX is equal to KN/m. 5. Considering the maximum flexural stress in compression, WMAX, is equal to 6. Considering the stress at the welded joint, wMex is equal to kN/m.
1. For the 15 foot copper bar shown in the figure below, find the total elongation (or shrinkage). The bar has a square cross section of 2" x 2" ( 16,000 lbs 4000 lbs 12' Punch Force 12000 lbs 2. A metal plate is 125 inch thick. What force is required to punch out a square piece 1" x 1"? The ultimate shear stress of the metal is 37,000 psi, and the ultimate tensile stress is 60,000 psi.
A round bar made of same material consists of 3 parts each of 100 mm, length having diameters of 40 mm, 50 mm and 60 mm respectively. If the bar is subjected to an axial load of 10 kN, the total elongation of the bar would be (E is the modulus of elasticity in KN/mm². (a) 4/1 1 1 + + (b) TE 16 25 36 (c) 1 0.4 1 1 + wwwwww + TE 16 25 36 (d) 4√2/1 1 1 www + wwwwwww + TE 16 25 36 40/1 1 1 + TE 16 25 36 — ===== + — mm mm mm mm
The pin-connected structure shown in the figure consists of a rigid beam ABCD and two supporting bars. Bar (1) is a bronze alloy [E = 95 GPa] with a cross-sectional area of A1 = 260 mm2. Bar (2) is an aluminum alloy [E = 69 GPa] with a cross-sectional area of A2 = 690 mm2. All bars are unstressed before the load P is applied; however, there is a 3-mm clearance in the pin connection at A. Assume L1 = 2000 mm, a = 1080 mm, b = 610 mm, c = 460 mm, and L2 = 1380 mm. If a load of P = 100 kN is applied at B, determine(a) the normal stresses in both bars (1) and (2).(b) the downward deflection of point A on the rigid bar.
A rectangular steel block is 3.0 inches long in the x-direction, 3.0 inches long in the y-direction, and 4.5 inches long in the z-direction. The block is subjected to a tri-axial loading of three uniformly distributed forces as follows: 50 kips tension in the x-direction, 60 kips compression in the y-direction, and 54 kips tension in the z-direction. If Poisson's ratio is 0.30 and E = 29 x 106 psi, find the uniformly distributed load that must be added in the x-direction to produced no deformation in the z-direction. Your final answer should include two decimal places
A composite shaft is made by slipping a bronze tube of 3.8-in. outer diameter and 2.5-in. inner diameter over a solid steel shaft of the same length and 2.5-in. diameter. The two components are then fastened rigidly together at their ends. What is the largest torque that can be carried by the composite shaft if the working shear stresses are 10 ksi for bronze and 14 ksi for the steel? For bronze, G = 6 x 10⁰ psi, and for steel, G = 12 x 10° psi.

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS