Three plates are welded together to form the section shown. Dimensions of the cross section are b = 5.1 in., d = 15.3 in., a = 3.6 in., and t = 0.8 in. For a vertical shear force of V = 40 kips, determine the shear flow through the welded surface at B. y d A B a b. Answer: ! kip/in.

Three plates are welded together to form the section shown. Dimensions of the cross section are b = 5.1 in., d = 15.3 in., a = 3.6 in., and t = 0.8 in. For a vertical shear force of V = 40 kips, determine the shear flow through the welded surface at B. y d A B a b. Answer: ! kip/in.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.8.1P: Compute the nominal shear strength of an M107.5 of A572 Grad 65 steel.

See similar textbooks

Related questions

Q: 9.9 A No. 32 (metric designation) reinforcing bar for concrete has a diameter of 32 mm. The bar is…

Q: Portions of a 0.25 × 0.25-in. square bar have been bent to form the two machine components shown.…

Q: toonges as aasm 12 mm thick plate is conected to two 8 mm thick plates, on either side through a 16…

Q: A solid brass E = 100 GPa axial member is loaded and supported as shown in the figure. Segments (1)…

A: Given data, W1 = 35 kN W2 = 14 kN W3 = 28 kN E = 100 GPa L1 = 1.8m L2 = 1.2 m L3 = 1.6 m To find…

Q: Three plates are welded together to form the section shown. Dimensions of the cross section are b =…

A: Given:- The magnitude of the shear force = V = 36 kips The dimensions of the cross-section are:- b =…

Q: Problem 2-4. For the following section, constructed of steel, determine: a) Moment at first yield…

Q: A hole is to be punched through a steel plate of 8 mm thickness. What is the least diameter of hole…

A: given steel plate thickness=8 mmcompressive stress=800 N/mm2ultimate shear strength=300 N/mm2

Q: Three plates are welded together to form the section shown. Dimensions of the cross section are b=…

Q: determine the minimum force P required to punch the slot. Punch O 575 kN O 675 kN O 724 KN Slug…

Q: 3. The aluminum block has the rectangular cross-section and is subjected to an axial compressive…

A: To determine: New length of 2 in side.

Q: A bolted connection between a vertical column and a diagonal brace is shown in the figure below. The…

A: Average shear stress = VA a. Find Shear force in one bolt ; V = 13 * P2 P = 6 k So, V = 1 k b. Find…

Q: Two aluminum plates, each having a width b = 7.5” and thickness t = 2”, are welded together as shown…

A: The diagram is shown below, Given data, b=7.5''a=5.0''t=2'' The…

Q: Three plates are welded together to form the section shown. Dimensions of the cross section are b =…

Concept explainers

Matrix Algebra for Structural analysis

Structural analysis is a process in which the effects of different loads and internal forces, acting on structures and their elements are determined. This method of analysis is effective in detecting the failure loads of the structural elements and the design can be altered before commencing the construction process, which ensures proper strength and safety of the structures.

Question

Three plates are welded together to form the section shown. Dimensions of the cross section are b = 5.1 in., d = 15.3 in., a = 3.6 in., and
t = 0.8 in. For a vertical shear force of V = 40 kips, determine the shear flow through the welded surface at B.
y
d
b
Answer:
9B = i
! kip/in.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 Introduction

VIEW

Step 2 Calculation

VIEW

Step 3 Result

VIEW

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Estimate the transverse tensile strength of the concrete in Problem 12.6.
The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
Use an elastic analysis and determine the maximum load in the weld (in kips per inch of length).
A tensile test was performed on a metal specimen with a diameter of 1 2 inch and a gage length (the length over which the elongation is measured) of 4 inches. The dam were plotted on a load-displacement graph. P vs. L. A best-fit line was drawn through the points, and the slope of the straight-line portion was calculated to be P/L =1392 kips/in. What is the modulus of elasticity?
Compute the nominal shear strength of an M1211.8 of A572 Grade 65 steel.
A W1422 acts compositely with a 4-inch-thick floor slab whose effective width b is 90 inches. The beams are spaced at 7 feet 6 inches, and the span length is 30 feet. The superimposed loads are as follows: construction load = 20 psf, partition load = 10 psf, weight of ceiling and light fixtures = 5 psf, and live load = 60 psf, A992 steel is used, and fc=4 ksi. Determine whether the flexural strength is adequate. a. Use LRFD. b. Use ASD.
Use an elastic analysis and determine the maximum load per inch of weld.
Use the composite beam tables and select a W-shape and stud anchors for the following conditions: Span length = 18 6 Beam spacing = 9 ft Total slab thickness = 51 2 in. (the slab and deck combination weighs 57 psf). Lightweight concrete with a unit weight of 115 pcf is used Construction load = 20 psf Partition load = 20 psf Live load = 225 psf Fy=50 ksi and fc=4 ksi A cross section of the formed steel deck is shown in Figure P9.8-9. The maximum live-load deflection cannot exceed L/360 (use a lower-bound moment of inertia). a. Use LRFD. b. User ASD.
A beam is part of the framing system for the floor of an office building. The floor is subjected to both dead loads and live loads. The maximum moment caused by the service dead load is 45 ft-kips, and the maximum moment for the service live load is 63 ft-kips (these moments occur at the same location on the beam and can therefore be combined). a. If load and resistance factor design is used, determine the maximum factored bending moment (required moment strength). What is the controlling AISC load combination? b. What is the required nominal moment strength for a resistance factor of 0.90? c. If allowable strength design is used, determine the required moment strength. What is the controlling AISC lead combination? d. What is the required nominal moment strength for a safety factor of 1.67?
The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen with a circular cross section. The diameter was 3 8 inch and the gage length (The length over which the elongation is measured) was 2 inches. a. Use the data in Table 1.5.2 to produce a table of stress and strain values. b. Plot the stress-strain data and draw a best-fit curve. c. Compute the, modulus of elasticity from the initial slope of the curve. d. Estimate the yield stress.
Use an elastic analysis and compute the extra load in the weld (in kips per inch of length) caused by the eccentricity.