The venturi meter is being used to measure the flow of fuel oil (sp gr = 0.858). The %3D differential gage fluid is water. The meter coefficient is 0.975. Compute the discharge if z is 16 inch. 3 inch 1 inch plic.com

Q: Research on how to compute for Reynold's number when the fluid flow is not in a pipe. Give at least…

A: When the fluid flow is not in a pipe ,Reynold's number can be computed using different formulas.

Q: Please define your CV for each problem. 1) A cylindrical tank (of inner diameter D and mass m,)…

A: The volume of fluid flowing through a given area of a cross-sectional area per unit time is called…

Q: 1. 'Water flows through a 12 inches by 6 inches venturi meter at the rate of 1.49 ft/s and the…

A:

Q: •.. 300 mm H20 150 mmg 425mm CHg C13-6) A 150mm diameter venturi meter is installed in a 300mm…

A: Given data, Dia of pipe, d1=300 mm=0.3 mdia of throat, d2=150 mm=0.15 mmercury differential,x=425…

Q: Probl Compute gage pressure at the center of pipe. For solution use: (a)British Unit, (b)Standard…

A: To Determine Gauge pressure in the centre of the pipe. a) In British unit ( psi ) b) In SI unit (…

Q: Compute the discharge through an orifice as shown.

A: Question is based on orifice meter. Diameter of orifice, and the diameter of section is given in the…

Q: Energy losses in pipe: L = 1.3m, D= 14 mm, ε/D = 0.007 Type of Reynold's Calculated Calculated pipe…

A:

Q: Determine the diameter of the nozzle, if the flowing fluid in the nozzle has a specific gravity of…

A: To Determine Diameter of the nozzle, D

Q: A direct-acting simplex pump has the following specifications: 8 in. x 4 in. x 8 in.; slip is 8%;…

A: Let us estimate the actual capacity of the Pump in step 2.

Q: help asap

A: Step 1:Step 2:

Q: Tow oil tanks are connected with a pip that has a constant radius, the readings of the two gauges…

A: Given data in question  Pressure at point 1 and 2 Elevation head at point 1 and 2 Specific gravity…

Q: From the following network data, determine the criticalpath, starting and finishing times, and TFs…

A: Network

Q: Kerosene (s.g.-0.82) enters the cylindrical arrangement of the figure shown at section 1, at 0.56…

A:

Q: Date Determination of Discharge Using a Venturi Meter tamula: Vol. %3D も PZ 29 trial #1 trial #2 H…

A:

Q: If (H= 11m) Find the discharge through pipes 1,2 and3.(neglect minor losses) Pipe 1 :L=70m Pipe 2 :L…

A:

Q: 27. Four pipes are connected in parallel. Their characteristics are as follows: Pipe no. Diameter…

A:

Q: 150mm dia. 300mm dia. 800 mm Water Mercury (SG = 13.6) A vertical venturi meter 150mm diameter is…

A: Discharge can be calculated by ; Q=A1A2A12 - A222gh A1 = π4(D1)2 =  π4(0.3)2  = 0.071m2 A1 = π4(D2)2…

Q: A pipe has a uniform diameter of 750 mm. The flow rate entering the pipe is 2.21 m^3/s. The exit…

A:

Q: passing the meter in 5 min. was 340 kg. A mercury differential gage connected to the inlet and…

A:

Q: Compute the meter coefficient, Cd.

A:

Q: A 60 MLD water treatment plant has 4 mechanical flocculators. The design criteria for each…

A: Detention time=25min Discharge=60MLD

Q: A 600m long pipe with a diameter of 600mm has a headloss of 1.20m. Detemine the following: a.)…

A: Given data- Length of pipe (L) = 600 m Dia of pipe (D) =600 mm = 0.6 m Headloss (hf) = 1.20 m

Q: URGENT Please answer this problem in 30minutes. I need correct answers with complete and step by…

A:

Q: Please answer in complete and clear solution thank you Question A fluid is flowing into an…

A: Given that  diameter of inverted conical tank d= 14in Height h= 24in Rate of flow = dv/dt = 7…

Q: Draw the EGL and HGL for the following system.

A: The flow of fluid includes movement of an unbalanced fluid. As long as unequaled forces are in…

Q: Example 3: For the setup shown(Figure below), Draw, ht, he , hp and velocity of flow ? Figure (7a)…

A:

Q: Find the head of internal mouthpiece (running fulI), a diameter and discharge of the mouthpiece are…

A: Given: Diameter, d = 150 mm = 0.15 m Discharge, Q = 32 litre/s = 0.032 m3/s

Q: 4m Oil (0.90) 3.75 mm Mercury (13.57) This vertical pipeline with attached gage and manometer…

A: Given data in question  Vertical pipe Specific gravity  Mercury To find out  Pressure at A in bars

Q: Cooling water having a density and viscosity of 998 kg/m3 and 0.95 cP is flowing thru a 25-mm med.…

A:

Q: Determine the discharge, HGL, and EGL. Water 20°C 4-cm-dia. wrought iron pipe 20 m Screwed elbows 40…

A:

Q: 7- If the viscose force is dominate in Reynolds number, the flow will be: O a) Laminar flow O b)…

A:

Q: 3. The total discharge from A to B in figure is 14 cfs. Determine the discharge in each pipe if the…

A: ● We have to calculate the value of discharge in each of the pipe.

Q: Q2) the airflow system is measured with a venturi having dimensions a 5.0 cm-diameter pipe. The…

A:

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.