O 4G l.خاصA sulms.su.edu.omFluid with the viscosity of 5X10-4 m2/s, isflowing in a pipe with the diameter of 35 cmand velocity of 2.5 cm/s. Calculate the headloss (m) for 100 m of the pipe.INext page* Quiz navigation O 4G l.خاصA sulms.su.edu.omFor transferring of water, a pump is installedin the height of 3 m above the surface of thewater. The pressure inserted on the surface ofthe water is 100 KPa, and the head loss beforethe pump is 4 m.a) Calculate the NPSH?b) Does the cavitation occur? (vapor pressureof water is 10 KPa)Discuss about your answer in part (b)I

Answered: Image /qna-images/answer/ed6bb600-972e-4c16-b461-74b74e664584.jpg

Answered: Fluid with the viscosity of 5X10-4…

Fluid with the viscosity of 5X10-4 m2/s, is flowing in a pipe with the diameter of 35 cm and velocity of 2.5 cm/s. Calculate the head loss (m) for 100 m of the pipe.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Oil having sp. gr. of 0.9 and viscosity v 0.0002 m2/s flows upward through an inclined pipe as shown. Determine the flow rate. Ans. 7.64 L/s 6 cm diameter P2 250 kPa 40 Pi 350 kPa
Water of temperature 30o is flowing with flow rate 0.055 liters/s in a straight 50mm diameter uPVC pipe of length 450. Determine the head loss for this length by using Darcy Weisbach formula, and Hazen-William's formula.
an orifice meter of 0.15 m diameter is fitted in a 0.3 m diameter pipe to measure the flow rate of water through it. if the pressure difference across the orifice is 10 m of water head, calculate the discharge in the pipe. Assume the coefficient of discharge of the orifice meter as 0.59.Answer is 0.15 m3/s , show solution with FBD
Oil flows at 62 L/s in a pipe of 175mm diameter and 50m length. SG of oil is 0.9 and viscosity is 0.04 Pa-sec. If head loss is 5.22m, determine: a) Mean velocity of flow = [ Select ] m/s b) Type of flow = [ Select ] %3D c) Friction factor = [ Select ] d) Velocity at the centerline of pipe = [ Select ] v m/s e) The shear stress at the wall of the pipe [ Select ] Ра %3D
A cylindrical tank of water is 20 m in diameter and 3.5 m tall. There is a 1.0 cm diameter hole at the bottom from which water is leaking. A feeder pipe at the top of the tank, 4.0 m above the ground delivers water at a rate of 0.02 m/min. Ir the tank is initially half full, tal what is the water flow rate in m^3/sec from the top feeder pipe? (bi what is the pressure at the bottom of the tank? (Hint: Bernoul's principle) () what is the water speed at the bottom? (d) what is the leaking flow rate at the bottom? fe) at what rate is the volume of water changing? (Assume the tank is open to air at the top)
Q.15 Water is flowing through two pipes one of 10 mm diameter and second of 5 mm diameter and both are discharging in 12 mm diameter pipe. The rate of flow in 10 mm diameter is 1.0 c.c./s. If the Reynolds number of 12 mm diameter pipe flow is 4000, determine the rate of flow in 5 mm diameter pipe. Consider kinematic viscosity equal to 6.5 x 10-7 m²/s.
A fluid of dynamic viscosity 2 x 10-5 kg/ms and density 1 kg/m³ flows with an average velocity of 1 m/s through a long duct of rectangular (25 mm x 15 mm) cross-section. Assuming laminar flow, the pressure drop (in Pa) in the fully developed region per meter length of the duct is
A PIPELINE WITH A PUMP LEADS TO A NOZZLE AS SHOWN. FIND THE FLON RATE WHEN PUMP DEVELOPS AN 80FEET HEAD. ASSUME HEAD LOST IN THE 8-INCH PIPE TO BE THERE TIMES ITS VELOCITY HEAD WHILE THE HEAD LOST IN THE 4-INCH PIPE TO BE TEN TIMES VELOCITY HEAD. FIND: a)COMPUTE THE FLOW RATE b) FIND THE PRESSURE HEAD AT THE SUCTION SIDE. PLEASE ANSWER IMMEDIATELY WITH COMPLETE SOLUTION THANK YOU!
QUESTION 2 , (a) In a rare pipe system design, there is such a case whereas the minor losses is greater than major losses. Describe the case and explain the reason why minor losses value is more than major losses value. (b) Water at 35°C flows steadily in a 4 cm,diameter pipe at velocity of 3.5 cm/s. The head loss is 0.5 m. Calculate: i) the length of theuotual pipe, ii) the pressure loss, and iii) the pumping power required to overcome this pressure drop.
Compute the head loss in a 5 inches pipe if it is necessary to maintain a pressure of 36.5 psi at a point upstream and 7 ft below where the pipe discharges water into the atmosphere at the rate of 1.963 cfs. Show the diagram.
Water with kinematic viscosity equal to 1.02 x 10-6 m2/s flows in a 1000m long, 150mm diameter pipe (E = 0.00005) at a rate of 30L/s. Solve for the head loss in the pipe.
A 25-mm-diameter pipe 35m long is used to convey oil. The oil has a density of 880kg/m³ and a kinematic viscosity of 0.25×10*m³/s. The discharge in the pipe is Q=24x10*m³/min. Given that the pipe is placed horizontally and there are no any minor losses. Determine the pressure drop between the entrance and exit of pipe.