A fluid of dynamic viscosity 2 × 10-5 kg/ms and density 1 kg/m³ flows with an average velocity of 1 m/s through a long duct of rectangular (25 mm x 15 mm) cross-section. Assuming laminar flow, the pressure drop (in Pa) in the fully developed region per meter length of the duct is

A fluid of dynamic viscosity 2 × 10-5 kg/ms and density 1 kg/m³ flows with an average velocity of 1 m/s through a long duct of rectangular (25 mm x 15 mm) cross-section. Assuming laminar flow, the pressure drop (in Pa) in the fully developed region per meter length of the duct is

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

What flows through a 0.305m vertical pipe downwards at a rate of 1.70 x 10^(-4) m^3/s exiting into the atmosphere. the pipes diameter remains constant at 0.013m. The velocity at the exit of the pipe was measured to be 1.28 m/s. Determine the pressure at the top of the pipe.
Question In fully developed laminar flow in a circular pipe, if the velocity at midway between the wall surface and the centerline is measured to be 6 m/s, then the velocity at the centre of pipe is
An oil flow rate of 0.012 m³/s is required in an industrial process. The flow system includes a pressure tank pushing the oil through 200 m of new ductile iron pipe (DIP: 15 cm diameter, square-edged entrance) to point "2" (atmospheric pressure) as shown in Figure P3.11.11. The sur face of the fluid in the tank (point "1") is at elevation 100 m and the end of the pipe (point "2") is at elevation 106 m. What air pressure will be needed over the fluid to produce the requisite flow? (S.G. (oil) = 0.84, v 2.03 x 106 m²/s, and e = 0.00012 m.)
A fluid of dynamic viscosity 2 x 10 kg/ms and density 1 kg/m² flows with an average velocity of 1 m/s through a long duct of rectangular (25 mm x 15 mm) cross-section. Assuming laminar flow, the pressure drop (in Pa) in the fully developed region per meter length of the duct is
A viscous liquid (p = 1.2x10°kg/m³, µ = 0.0048 Pa.s) flows at a rate of 10ml/s through a horizontal, 4 mm diameter tube. The pressure drop along a 1 m length of the tube which is far from the tube entrance so that the flow is fully developed is _(kPa)
Consider the pressurized horizontal pipe network shown below. Pipe 2 is arranged in parallel with Pipe 3. The characteristics of each pipe are summarized in the table. The flow of water at Node A is Q = 10 cfs and the pressure head at Node A is yA = 180 feet. The temperature of the water is 60° F. a) Determine the flow in cfs in Pipe 2. b) Determine the flow in cfs in Pipe 3. c) Determine the friction head loss hric in feet in Pipe 1. d) Determine the friction head loss hfic in feet in Pipe 2. e) Determine the friction head loss htric in feet in Pipe 3. f) Determine the friction head loss hfric in feet in Pipe 4. g) Determine the pressure head ys in feet at Node B. h) Determine the pressure head yc in feet at Node C. i) Determine the pressure head yo in feet at Node D. Flow Friction Pressure Diameter Length Pipe (inches) (feet) Friction (cfs) head Нead factor f Kpipe loss (feet) Node (feet) 1 16 500 0.012 10 A 180 12 1000 0.014 B 10 1000 0.015 16 500 0.020 10 D Pipe 2 Node Node Node…
Air in a room at T0 = 290 K and P0 = 90 kPa is to be drawn by a vacuum pump through a 3-cm-diameter, 2-m-long adiabatic tube equipped with a converging nozzle at the inlet. The flow in the nozzle section can be approximated as isentropic. The static pressure is measured to be 87 kPa at the tube inlet and 55 kPa at the tube exit. Determine the mass flow rate of air through the duct, the air velocity at the duct exit, and the average friction factor for the duct.
An ideal liquid flowing through a pipe A of cross-section 0.2m² with velocity 10m/s enters a T-junction. One side of the T-junction B has cross-section area 0.1m² and the other side Chascross-section area 0.05m². If the velocity of water in C is 15m/s then in B the velocity is
Consider the pressurized horizontal pipe network consisting of three pipes arranged in series. The characteristics of each pipe are summarized in the table. The flow of water at Node A is Q = 5 cfs and the pressure head at Node A is yA = 200 feet. The temperature of the water is 60° F. a) Determine the friction head loss hfric in feet in Pipe 1. b) Determine the friction head loss hfric in feet in Pipe 2. c) Determine the friction head loss hfric in feet in Pipe 3. d) Determine the pressure head ys in feet at Node B. e) Determine the pressure head yc in feet at Node C. f) Determine the pressure head yo in feet at Node D. Flow Friction Pressure Diameter Length Friction (feet) (cfs) head Нead Pipe (inches) factor f Kpipe loss (feet) Node (feet) 1 16 500 0.011 5 A 200 2 12 1000 0.013 B 3 10 750 0.015 D Node Node Node Node A в D 5 cfs 5 cfs Pipe 1 Pipe 2 Pipe 3