In a two dimensional incompressible, steady flow, stream lines are drawn so that they are 20 mm apart (location A) and velocity at that location is 5.0 m/sec. What is the velocity in the same fluid where the stream lines are 16 mm apart (Location B). If pressure at A is 200 kPa, find out Example 6.15 the pressure at B. Assume the density of fluid is 900 Kg/m³.

In a two dimensional incompressible, steady flow, stream lines are drawn so that they are 20 mm apart (location A) and velocity at that location is 5.0 m/sec. What is the velocity in the same fluid where the stream lines are 16 mm apart (Location B). If pressure at A is 200 kPa, find out Example 6.15 the pressure at B. Assume the density of fluid is 900 Kg/m³.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Consider the two-dimensional flow of an inviscid, incompressible fluid described by the superposition of a parallel flow of velocity V0, a source of strength q, and a sink of strength −q, separated by a distance b in the direction of the parallel flow, the source being upstream of the sink. (a) Find the resultant stream function and velocity potential. (b) Sketch the streamline pattern. (c) Find the location of the upstream stagnation point relative to the source.
In the illustration: A В 2 D All friction factor f - 0.02 All pipe lengths L- 250m Diameter of Pipe A= 400mm with Flow Rate at Pipe A = 700 L/s Diameter of Pipe B = 300mm Diameter of Pipe C = 200mm Diameter of Pipe D = 400mm Solve for - difference in elevation in meters in between reservoirs.
Note:hand written solution should be avoided.
An oil flow rate of 0.012 m³/s is required in an industrial process. The flow system includes a pressure tank pushing the oil through 200 m of new ductile iron pipe (DIP: 15 cm diameter, square-edged entrance) to point "2" (atmospheric pressure) as shown in Figure P3.11.11. The sur face of the fluid in the tank (point "1") is at elevation 100 m and the end of the pipe (point "2") is at elevation 106 m. What air pressure will be needed over the fluid to produce the requisite flow? (S.G. (oil) = 0.84, v 2.03 x 106 m²/s, and e = 0.00012 m.)
A duct of diameter 0.8 m carries gas (p = 1.3 kg/m³). At one point, the duct diameter reduces to 0.74 m. Starting from Bernoulli's equation, estimate the velocity of flow in the reduced section, and the mass flow rate (=pQ) through the duct if the pressure difference between a point upstream of the reduction and another point at the reduction is equivalent to 30 mm of water.
3) An incompressible flow velocity field is given as 1 1 [m/s] r r where r is in meters. (a) Calculate the mass flow rate through the cylindrical surface at r =1 m from z = 0 to z =1 m as shown in Figure A (b) Show that mass is conserved in the annular control volume from r = 1 m to r = 2 m and z = 0 to z = 1 m as shown Figure B a 2 m. I m 1 m 1 m 1 m
The water flow rate in the pipe will be measured using the pitot tube system given in the figure. At point 1, the velocity is zero and represents the stationary point. Since there is mercury with a density of 13600 kg/m3 in the manometer and the height of the manometer is read 0.06, calculate the volumetric flow rate of the water flowing in the pipe with a diameter of 0.2 m. (ρwater = 1000 kg/m3)