A fluid flows downward with the rate of Q=0.015 m/s in a smooth vertical pipe with the length of l. (a) Find the diameter of the pipe if the pressure drop (p1- p2) is zero. (Hint: Use Moody Chart with the initial guess of f=0.02. Two iterations are enough) (b) If the pipe outflow hits a fixed vane as shown in the figure, what would be the horizontal and vertical forces (Fx, Fy) on the vane? (p = 1000 kg/m³; µ = 0.001 kg/m. s; a = 30 deg)

A fluid flows downward with the rate of Q=0.015 m/s in a smooth vertical pipe with the length of l. (a) Find the diameter of the pipe if the pressure drop (p1- p2) is zero. (Hint: Use Moody Chart with the initial guess of f=0.02. Two iterations are enough) (b) If the pipe outflow hits a fixed vane as shown in the figure, what would be the horizontal and vertical forces (Fx, Fy) on the vane? (p = 1000 kg/m³; µ = 0.001 kg/m. s; a = 30 deg)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Answer must correct. Fast Don't hold the Question
(b). Figure 1 shows a reticulation system. Estimate the flow rate in each pipeline using Hardy-Cross Method and Hazen-William formula up to two iterations. Adopt Hazen-William coefficient, C, as 100. The lengths and diameters for pipes AB, BC, CD, and AD are as follows: Pipe AB: length = 950 m and diameter = 250 mm Pipe BC: length = 750 m and diameter = 200 mm Pipe CD: length = 750 m and diameter = 200 mm Pipe AD: length = 900 m and diameter = 250 mm 40 L/s 40 L/s C B D Figure 1: Reticulation system 50 L/s 130 L/s
Problem 2: Manometer and Pipe S = 0.8 300 mm dia Water flows past a manometer as shown. The manometer fluid is oil with s = 0.8. If the manometer reading Rm= h = 0.12 m, what is the water velocity at the centerline of the pipe?
Note:hand written solution should be avoided.
Problem 7.7 A mixing basin in a sewage filtration plant is stirred by a mechanical agitator with a power input W = F. LIT. Other parameters describing the performance of the mixing process are the fluid absolute viscosity μ=F.T/Ľ², the basin volume = Ľ³, and the velocity gradient G=1/T. Determine the form of the dimensionless relationship.
The circular water pipes shown in the sketch are following full. The velocity of flow (in m/s) in the branch pipe "R" is V = 6 m/s dia = 4 m – મ N=? R V = 5 m/s dia= 2 m
Q. Determine the kinematic viscosity at the average temperature and determine the Reynolds number and type of flow using the data shown below and table values: Data obatined from a Reynolds Number test: Water temperature at the beginning of the experiment = 25 oC Water temperature at the end of the experiment = 30 oC The Volume of water collected in 25 seconds = 240 ml Pipe diameter, d= 10 mm. (use eq'n reynold's number, Re = VD/v
The circular water pipes shown in the sketch are flowing full. The velocity of flow (in m/s) in the branch pipe "R" is PI V = 6m/s, dia = 4m - = V = ? R Q V = 5m/s dia = 2m
Water is designed to flow in a HDPE pipe of length 267 m as shown in the figure in Problem 10. The flow velocity is limited to 3.3 m/s. By using Darcy Weisbach and Hazen William's formula, determine the pipe diameter and the flow rate.
A duct of diameter 0.8 m carries gas (p = 1.3 kg/m³). At one point, the duct diameter reduces to 0.74 m. Starting from Bernoulli's equation, estimate the velocity of flow in the reduced section, and the mass flow rate (=pQ) through the duct if the pressure difference between a point upstream of the reduction and another point at the reduction is equivalent to 30 mm of water.
3) An incompressible flow velocity field is given as 1 1 [m/s] r r where r is in meters. (a) Calculate the mass flow rate through the cylindrical surface at r =1 m from z = 0 to z =1 m as shown in Figure A (b) Show that mass is conserved in the annular control volume from r = 1 m to r = 2 m and z = 0 to z = 1 m as shown Figure B a 2 m. I m 1 m 1 m 1 m