Oil (s=0.80) and viscosity (u = 0.098 Pa - sec) flow from a reservoir of surface elevation 100 meters to one with a surface elevation of 94 meters through a 150 mm Ø smooth pipe width is 300 meters long. Determine the average velocity in the pipe.

Oil (s=0.80) and viscosity (u = 0.098 Pa - sec) flow from a reservoir of surface elevation 100 meters to one with a surface elevation of 94 meters through a 150 mm Ø smooth pipe width is 300 meters long. Determine the average velocity in the pipe.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine a. Velocity at the pipe with 8 in. diameter in ft/s. b. Pressure at point D in psi c. Flow rate in cfs d. Velocity at the pipe with 18 in. diameter in ft/s
Oil having sp. gr. of 0.9 and viscosity v 0.0002 m2/s flows upward through an inclined pipe as shown. Determine the flow rate. Ans. 7.64 L/s 6 cm diameter P2 250 kPa 40 Pi 350 kPa
Please indicate the given, assumption and iluustration A steel pipe, 3.5 km long x 80 cm diameter x 1 cm wall thickness, conveys water at the rate of 1.75 m3/s. Determine the increase in pressure when a valve provided at the downstream end of the pipe is closed instantaneously. Consider pipe to be elastic and take bulk modulus of water K = 2x109 N/m2; Modulus of elasticity of steel E = 2x1011 N/m2. After determining the surge of pressure in the pipe, compute the following: A) The Longitudinal Stress of the Pipe in Pascal. B) The Circumferential Stress of the Pipe in Pascal.
Oil flows at 62 L/s in a pipe of 175mm diameter and 50m length. SG of oil is 0.9 and viscosity is 0.04 Pa-sec. If head loss is 5.22m, determine: a) Mean velocity of flow = [ Select ] m/s b) Type of flow = [ Select ] %3D c) Friction factor = [ Select ] d) Velocity at the centerline of pipe = [ Select ] v m/s e) The shear stress at the wall of the pipe [ Select ] Ра %3D
A cylinder is placed in a steady water flow as shown. Calculate the pressure difference PB - PA in psi if the flow speed at A is 10 ft/sec. .A O 1.04 O 1.53 0.67 1.92 0.82 O 1.74
A cylindrical tank of water is 20 m in diameter and 3.5 m tall. There is a 1.0 cm diameter hole at the bottom from which water is leaking. A feeder pipe at the top of the tank, 4.0 m above the ground delivers water at a rate of 0.02 m/min. Ir the tank is initially half full, tal what is the water flow rate in m^3/sec from the top feeder pipe? (bi what is the pressure at the bottom of the tank? (Hint: Bernoul's principle) () what is the water speed at the bottom? (d) what is the leaking flow rate at the bottom? fe) at what rate is the volume of water changing? (Assume the tank is open to air at the top)
len3
Oil with specific gravity of 0.88 flows through a pipe which changes from 6 in. at section A to 18 in. at section B. Section A is 12 ft lower than B and the pressures are 13.2 psi and 8.75 psi, respectively. If the flow rate is 5.17 cfs, determine (a) The velocity (ft/s) at section A, (b) The velocity (ft/s) at section B, (c) The head lost (ft) between the two points, and (d) The direction of flow. Is it from A to B or B to A?
A municipality wants to determine the flow rate into the plant based on pipe size, elevation difference, and assumed roughness, for the water supply reservoir is shown in the figure below. The pipe is an old 4-inch diameter Cast Iron with a Hazen Roughness coefficient of 100 & 223 feet long. The difference in elevation is 62 feet. The pipe has a strainer at the entrance (k-1.9), a valve (k=8.6), a check valve (k = 2:7) and 3- 90° bends (k-0.83). The flow exits into a receiving pond at the WTP. Provide the flow rate in Gallons Minute. per WTP Az
nat3
At Point A, in a pipeline carrying water (y=62.4 Ib/ft^3) the diameter is 4.0 ft, the pressure is 10 psi, and the velocity 4 ft/s. At point B, 6ft higher than point A, the diameter is 2 ft and the pressure is 2psi.determine the following:(a)quantify the losses in this system and (b) is the flow going from Point A to Point B or from point B to point A. why?