Cooling water having a density and viscosity of 998 kg/m3 and 0.95 cP is flowing thru a 25-mm med. wt. steel pipe (I.D. = 0.0272 m). The pipeline is equipped with a venturi meter of 10 mm throat diameter and a U-tube mercury manometer. If the water flows at a rate of 25.0115 liters per minute, determine the corresponding manometer reading.

Cooling water having a density and viscosity of 998 kg/m3 and 0.95 cP is flowing thru a 25-mm med. wt. steel pipe (I.D. = 0.0272 m). The pipeline is equipped with a venturi meter of 10 mm throat diameter and a U-tube mercury manometer. If the water flows at a rate of 25.0115 liters per minute, determine the corresponding manometer reading.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Fluid mechanics ضهذعسو
3: Answer either A- A submerged pipe outlet has the following data: F.S.L of distributary= 100.00 m, F.S.L of watercourse 99.90 m, length of the pipe=9 m, diameter of pipe- 20 cm, coefficient of friction=0.005. 1- Find the discharge through the outlet. F: 0.005 2- Find the behaviour and sensitivity of the outlet. B- A trapezoidal channel with bottom width 3.5 m and side slopes IH:IV on the left and 1.5H:IV on the right. Use n=0.016 and bed slope of 2.6/10000. The channel carries a discharge of 8 m³/s. Determine the depth of the channel.
In a test to determine the discharge coefficient of a 50 mm x 12.5 mm horizontal venturi meter, the total weight of water passing the meter in 5 min. was 340 kg. A mercury differential gage connected to the inlet and throat of the meter showed an average mercury difference during thatrime or 364 mma. Compute the velocity of the throat (m/s)b. Compute the theoretical discharge (m3/s)c. Compute the meter coefficient.
Water flows without viscous effects from the nozzle, as shown in Figure Q2(b). The pressure meter shows a reading of 80.7kPa(gauge). Water jet is exposed to atmospheric pressure.
A 63 cm dia. pipe is fitted to a Venturi meter with a throat diameter of 23 cm as shown. During a 13 min. test, it discharges 673 m3 of water. Pressure at the large section is equivalent to 33 m. of water. At the throat, a negative pressure corresponding to 23 cm of mercury is occuring, Compute the meter coefficient, Cd.
Subject water system design Answer the second question
Kindly answer this. Thank you.
Question 5 Figure 5 shows a header tank in a laboratory. a) Determine the discharge when filling the tank using the main water. b) If the tank bottom is rectangular (1m x 3m) and the required depth is 0.75 m, determine the time needed to fill the tank. c) With respect to pipe flow, discuss how viscosity and pipe surface condition affect the flow velocity. Pipe diameter AC: D = 22 mm; Mains water pipe diameter (BC): 100mm Mains water pressure head at B: 35 m 3.4 m Figure 5. for Question 5 3.5 m B Mains water
20:22 CE272-8-conserv... ■■ Turk Telekom Х 3/4 5 %71 Example 5.2 A circular pipe of radius R has a perforated section of length L. The velocity distribution of flow at section (1) is given by u Umax r The discharge per unit length of the perforated section is qr. Determine: a) the average velocity Vax at section (2) b) the difference between the mass flux rate of sections (1) and (2). <] Umax Rr u(r) R
c) For the system shown in Figure 3.1, calculate (i) the volume flow rate of water from the nozzle and (ii) the pressure at point A. 24m Wae 36m 0m OD 5m al meter Figure 3.1
Quick please
1) Determine the flow in Ips on the orifice between the 2 tanks shown below AIR 25kPa AIR 10kPa OIL S=0.80 OIL S=0.80 WATER WATER ORIFICE C0 60 D-50mmo 2,8m 2m 1.5m WL