4m Oil (0.90) 3.75 mm Mercury (13.57) This vertical pipeline with attached gage and manometer contains oil and mercury as shown. The manometer is open to the atmosphere. There is no flow in the pipe. Express the pressure reading at A in bar. Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: bar Decimal Places required in the final answer: 3

4m Oil (0.90) 3.75 mm Mercury (13.57) This vertical pipeline with attached gage and manometer contains oil and mercury as shown. The manometer is open to the atmosphere. There is no flow in the pipe. Express the pressure reading at A in bar. Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: bar Decimal Places required in the final answer: 3

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

URGENT Please answer this problem in 30minutes. I need correct answers with complete and step by step solution. Box the final answers. Do not shortcut your solution. I will give an upvote if it satisfies. Thank you! Oil is flowing upward through a Venturi meter as shown. Assume a discharge coefficient of 0.984. a. Compute the change in pressure head between 1 and 2 in meters of oil. b. Compute the velocity at the throat. c. Compute the rate of flow of oil.
Subject : Fluid mechanics Give me right solution according to the question
Please use the second photo as a format of solution. Please write properly. THANKS!
Compute the pressure @ point n ( Pn ) as shown by the differential manometer in KPa if pressure @ point m ( Pm ) is equal 1027.66 mm Hg. air plpeline where: a= 12" b=3,2 C-4.0 d- 12 m mercury density (16 300 kghm) water pipeline
1. A pump station design fills a pressurized water tank by pumping water from a reservoir. The flow rate is 0.75 cfs. The pump is 10 feet above the reservoir, and the water tank is 100 ft above the pump. The pressure in the water tank is 10 psi. The suction and discharge lines are both (actual diameter) 6-inch Sch 40 steel (pipe roughness = 0.00015 ft). Use a kinematic viscosity of 1.21 x 10-5 ft²/s. Total pipe length is 200 ft. The suction line is 10 ft. You must account for friction loss, but you can neglect the minor losses. a. What is the head added by the pump in ft? b. What is the power added by the pump in HP (recall 1 HP = 550 ft*lb/s)? 110 ft 10 ft 0 ft
Give me right solution according to the question. Note: If you are 100 % confident then you can solve it otherwise leave it for someone. Thank you
SUBJECT: HYDRAULICS FINALS ANSWERS MUST BE 3 DECIMALS AND BOX IT BADLY NEED IT ASAP EXPERTS. THANK YOU
M MEQ2.jpg 200mmø 690mm 300 mm 400 mmø Z Hg (13.6) A 200mm diameter venturi meter is installed in a 400mm diameter vertical main pipe as shown. If the deflection of mercury (SG = 13.6) at the manometer reads 300mm and the vertical distance between point 1 and point 2 is 690mm, determine the discharge in the system assuming a head loss of 600mm. Hide answer choices a A) 307.36 L/s B) 279.84 L/s No Answer among the choices D) 224.67 L/s 256.29 L/s O O O O C
Question 6 In the schematic below, water flows through the pipe and enters a sudden contraction nozzle. To hold the nozzle in place, calculate the axial component of an anchoring force (FA) that would be necessary. Provide a sketch of your control volume. p = 1.940 slugs/fts, 1 ft = 12 inches, 1 lb-s? = 1 slug-ft Section (1) Uniform flow P-75[psi] V,-25[ft/s] Section (2) Uniform flow P2=0 [psi] V=100[ft/s] D;=3 [in] Flow in circular pipe Flow in circular pipe Sudden contraction nozzle
Fluid Mechanics Question
blö 8 Question Liquid ( S 1.5) A U-tube differential manometer containing two pipes at A and B. Pipe A contains a liquid of specific gravity 1.5 under a pressure of 100 kPa. Pipe B contains oil of specific gravity 0.8 under a pressure of 350 kPa. Calculate the difference in mercury level (h) in the B differential manometer, as shown in the figure. -Oil (S-0.8) Mercury (S-13.6)
The height of the fluid inside the tube after immersion is 1⁄8 the height of the cylinder glass tubing. It was immersed into a tank of a cleaning solvent with specific gravity of 0.83. The remaining length of tube above the surface is 6 cm. Determine the gage pressure after immersion. Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: kPa Decimal Places required in the final answer: 3