A plate is used as a tension member, to carry a deadload = 300 KN and live load of 260 KN. Steel used isA36, F,= 248 MPa, Fu = 400 MPa. If the width of the tension plate is 210 mm, determine:a) The thickness of the plate based on NSCP 2015 ASD, bult used is M20.--b) The thickness of plate based on NSCP 2015 LRFD. Bolt used is M20.--210 mm-Tension PlateM20 bolts

given - a bolted plate connection required- to find thickness of plate

Answered: ) The thickness of the plate based on…

) The thickness of the plate based on NSCP 2015 ASD, bult used is M20.--- ) The thickness of plate based on NSCP 2015 LRFD. Bolt used is M20.--

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Two plates of Steel A72 Gr 50 are connected with each as shown in Figure 5. E70XX Electrodes were…

A: Given:- Steel A72Gr500 fillet weld=7/16 To find:- design strength by LRFD and ASD

Q: The bolted type connection will be used to assemble the given steel members. If PArmax = 8.36 t;…

Q: The plate shown is 8 in wide and 1/2 in thick. The bolts are 7/8 in. The smallest net area (An) of…

A: Given:- width of plate =8 inthickness of plate =1/2 inBolts diameter size = 7/8 inA36 plateTo…

Q: 1.A tension member is 25 mm thick plate as shown. The bolts are 20 mm. diameter high-strength bolts.…

A: Plate 130 mm x 25 mmbolt diameter, db = 20 mmA36 grade of steel:fy = 250 MPafy = 400 MPaTo find:a)…

Q: The connection shown below uses 1-inch-diameter Group A bolts with the threads not in the shear…

A: LRFD It applies Ultimate factored loads to design. Evaluate forces and stress using yielded…

Q: For the connection shown, the load is 70% live load and 30% dead load. What weld size is needed if…

A: Solution: Given: LL = 70% x 8 = 5.6 kips DL = 30 % x 8 = 2.4 kips A 36 steel Assume t = 1/2 in E70…

Q: PROBLEM 9.9 9.10 In the bolted connection of Figure 9.12, assume that the bolts are in. in diameter…

Q: Consider the brace connection in Figure 4. (a) Design number of required M16 bolts to carry the full…

A: Tensile load for designing the bolt Pu = Ag for PFC100 section, Ag = 1060 mm2 ( from HRSSP 8th…

Q: WT12×153 05 WT12×153 Determine the design strength of two WT-shapes (WT12×153) connected by plates…

A: We have to determine the design strength of two WT-shapes (WT12x153) connected by plates with 1 in…

Q: Determine the total LFRD design strength and the total ASD allowable strength of the 5/16 – in E70…

A: We will solve this question in step no. 2

Q: A UNS G10350 steel shaft, heat-treated to a minimum yield strength of 75 kpsi, has a diameter of 1-…

A: Solution:-UNS G10350Minimum yield strengthσymin=75kpsiShaft rotates n=613rpmd=2316P=53hpSafety…

Q: o normal temperatures but wet in-service conditions. Assume =0.95 and the geometry factor is CA=1.…

A: 1 Area of the plate Ag Ag = 4×10 = 40 in2for A36 grade steel fy =36000…

Q: Compute the maximum acceptable tensile SERVICE LOAD that may act on a single tee section that is…

A: Given- Properties of WT- 12×38Ag=11.2 in2y'=3.0 inbf=8.99 inA992 steel-fy=50 ksiFu=65 ksiLL=3DL

Q: Material Strengths: Fy= 248 MPa, Fu = 400 MPa The channel (C180X14.6) is connected with four M16…

Q: In the figure shown, the bolts are 3/4-inch in diameter, and A36 steel is used for all components.…

A: Introduction- Overall shearing capacity of a bolt is the amount of force required to split the bolts…

Q: PA PL ¹½/2 x 6 3″ 2 PL ¾/16 x 3 P

A: Tension member splice is made with weldsThe inner member is a and each outer member is a The live…

Q: 1. A riveted lap joint is shown in the figure below. The rivets used are A502, Grade 2, hot-driven…

Q: A 3/4 in (thickness) X 5 in (height) steel plate is connected to another one through two bolts of…

Q: a. Under a heavy vibrating loads it is possible that a fully tensioned bolt may come loose. As a…

A: Under heavy vibration or dynamic loading bolted connections and welded are not preferred. Because…

Q: 1- A structural analysis was done for the steel section whose shape and characteristics are shown…

Q: An 18 mm thick plate is joined to a 16 mm plate by 200 mm long (effective) butt weld. What is the…

A: 18 mm thick plate joined to 16 mm plate 200 mm long, Le=200 mm,γmw=1.25 (shop welding)te=tmin=16 mm…

Q: 1½" 3"<3"→ -1½" 2" С7x 12.2 O O 2" t = ½"

A: Calculation Gross-section nominal strength; Pn = FyAg=50×(3.6)=180 kips Calculation of Net section…

Q: Question Design an optimize welded connection with fillet weld and resist the dead load of 20 kips,…

A: Dead Load = 20 kipsLive Load = 40 kipsWind Load = 10kipsGiven L Section = 6" x 4" x (7/16)"The…

Q: 4. Calculate the design strength (p.Pn) of W24X76 with length of 12 ft. and pinned ends. A572…

Q: A bearing type connection is shown in Figure 3.19. The diameter of A 325 bolts is 22 mm and the A572…

A: Tensile capacity, the maximum load that a material can support without damage when being determined…

Q: loads shown. Does this member have enough strength Assume that . a) Per LRFD b) Per ASD

A: For grade A 36,Dead load =95 kipsLive load =9 kipsNeed to findDoes member have enough strength.(a)…

Q: Calculate the tightening torque for an SAE 5, ASTM449, 13UNC grade bolt with a diameter of 1/2 inch.…

A: The application of preload to a fastener by the turning of the fastener's nut. Friction points…

Q: An angle L5x5x% tension member of A36 steel is connected to a gusset plate with six 3/4-inch…

A: Tension member L5x5x5/8A36 steel.Bolt diameter, db = 3/4 in6 bolts spaced 3 inThe length of the…

Q: The slip-critical bolted connection is shown below. The bolts are M24-8.8 and the tension member is…

Q: A 6x6x9/16 angle as shown is subjected to tensile load and is to be welded with 1/4" weld (EXX of…

A: Note- Since we answer one question at a time so we will answer the first one. Please resubmit…

Q: 5) Calculate P the allowable tensile load for the butt joint shown. Each A325-N high-strength bolt…

Q: Design a welded connection for an MC9x23.9 of A572 Grade 50 steel connected to a 3/8-inch-thick…

A: A572 grade 50 steel connected to 3/8 inch thick gusset plateThe gusset plate is A36 steelTo…

Q: A C15x50 (d=381mm and tw=18.19mm) tension member is to be connected by fillet welds to a 20mm thick…

A: Solution: Given;

Q: Compute the maximum acceptable tensile SERVICE LOAD that may act on a single tee section that is…

A: Answer In order to calculate the minimum acceptable tensile service load we need to first find the…

Q: Compute the service load capacity P for the welded bracket of the accompanying figure. The load is…

A: Given that :-A figure with welded bracket is given with following specifications.Live load = 70…

Q: The connection shown is subjected to a tensile force of P = 100 kN. The allowable shear stress for…

A: Area = Force/ Shear stress

Q: A plate 400 x 12 mm is to be connected to a plate of the same width and thickness by 34 mm diameter…

Q: The bolted connection shown must support an applied load of P = 5300 kN. The average shear stress in…

A: The values and diagram given in the question are as follows: Applied load(P)=5300 kN or 5300*103 N…

Q: The tension member shown is a PL 5/8 x 10, and the steel is A36. The bolts are 7/8-inch in diameter.…

A: Member =58×10 Steel A36 → Fy=36 ksi → Fu=58 ksi Bolts are 78 in. diameter.

Q: he anchors used in GFRC panels are typically a. two-piece anchors. b. one-piece anchors. c. either…

Q: Grade: 10.9 Included I Grade: S235 ace Class: C atio of the mean installed bolt pretension to the…

Q: E- S G Rigd Aluin plates end plde

A: Find h and total load P?

Q: Design a double angle tension member that is fillet welded to a gusset plate. Assume that the angles…

A: 1).Design and select a trial tension member See Table 5-8 on page 5-49 of the AISC manual. - Select…

Q: The connection shown below uses 1-inch-diameter Group A bolts with the threads not in the shear…

Q: Problem 3. An un-equal leg angle L8x4x½ made of ASTM A242 steel (Fy = 50 ksi, Fu = 70 ksi) is used…

A: Unequal leg angle, L 8 x 4 x 1/2" of ASTM 242 steel, Fy=50 ksi , Fu= 70ksi To Find: (a) Factored…

Concept explainers

Bars

In civil engineering, bars refer to steel reinforcement bars or rebars. These are structural members primarily used for reinforcement purposes in masonry works. A bar is characterized by its cross-sectional area, which is negligible compared to its length. Bars are usually manufactured by steel which is uniform throughout the length, or by meshing multiple steel wires. Other materials of the bar include carbon steel, glass fiber, carbon fiber, and basalt fiber. The reinforcing bars are coated with epoxy resins and other materials to enhance some of their properties including corrosion resistance.

Question

A plate is used as a tension member, to carry a deadload = 300 KN and live load of 260 KN. Steel used is
A36, F,= 248 MPa, Fu = 400 MPa. If the width of the tension plate is 210 mm, determine:
a) The thickness of the plate based on NSCP 2015 ASD, bult used is M20.--
b) The thickness of plate based on NSCP 2015 LRFD. Bolt used is M20.--
210 mm
-Tension Plate
M20 bolts

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A C8X11.5 single channel section is bolted to a gusset plate with M22 bolts. Assume A572 Gr.50 steel and 10mm gusset plate. Find the following values • The design block shear strength of the channel • The allowable block shear strength of the gusset plate 30, 65 , 65 30 60 80 O O O 60 C8X11.5 (AISC Designation)
In a bolted wood connection, which of the following is considered the main member? O The member with highest specific gravity The member with the smaller dimension along the bolt The main and side member terminology does not apply to bolted connections The member with the larger dimension along the bolt
For the cross section shown, calculate the tensile capacity of the steel plate. Assume that the bolt hole is 1/16 inch larger than bolt diameter. Plate 1/2" x 11" .T 7/8" dia. bolt, typ. ASTM A325N
A plate is used as a tension member, to carry a deadload = 300 KN and live load of 260 KN. Steel used is A36, Fy= 248 MPa, Fu = 400 MPa. If the width of the tension plate is 210 mm, determine: a) The thickness of the plate based on NSCP 2015 ASD, bult used is M20.------ b) The thickness of plate based on NSCP 2015 LRFD. Bolt used is M20.-------- I M20 bolts- 210 mm -Tension Plate
If the thickness of plate to be connected by a rivet is 16 mm, the suitable size of rivet will be (a) 16 mm (c) 24 mm (b) 20mm (d) 27 mm
Bolt properties: M14 x2 ISO 5.8 (a) Determine a suitable length for the bolt, use preferred size. (b) Determine the bolt stiffness. Q # 3 15KN Rotating shaft Pillow block Metric (ISO) screw (c) Determine the stiffness of the 15 members. (d) Evaluate Yielding, Load and Joint Separation factor of safeties if the joint is permanently bolted. Steel 1cm Som Grey Cast Iron CLO-3, PLO-2
4. Is the bearing-type connection shown in the right figure sufficient to resist the 200 k load which passes through the center of gravity of the bolt group? P₁-200 k 3 Eight 7/8-in A325X bolts
10 mm fillet welds Determine the design capacity of the welded lap steel connection shown below. All steel plates are 50X10mm dimension. Both fillet welds are 10mm E48XX SP, continuous across the full plate width. If the connection was tested to failure, which component would fail first.
An A36 steel plate with width of 400 mm and thickness of 12 mm is to beconnected to a plate of the same width and thickness by 34 mm diametersbolts, as shown in the figure (next slide). The holes are 2 mm larger thanthe bolt diameter. The yield strength of the steel plate is Fy = 248 MPa.Assume allowable tensile stress on net area is 0.60Fy. It is required todetermine the value of b such that the net width along bolts 1-2-3-4 isequal to the net width along bolts 1-2-4.a. Calculate the value of b in mm.b. Calculate the value of the net area for tension in plates in mm².c. Calculate the value of P so that the allowable tensile stress on net areawill not be exceeded.(Use at least 2 decimal points on your answers.)
If the design tensile strength Phi Pn of a tension member is controlled by rupture failure. Which of the following actions will NOT increase its capacity? using welds instead of bolts using larger cross section of the member increasing strength of steel using thicker gusset plate
Load and resistance Factor design-tension members Q- Look into the block shear failure mode on the angle L4X4X linked to the 1-inch gusset plate with three 1-inch diameter bolts. Steel A36 is the substance.
The block shear strength of the tension member as shown in figure is (round off to two decimal places). Assume grade of plate Fe410. 45 mm 35 mm 50 mm 100 mm ISA 80 x 50 x 8 mm (M20 bolt of grade 4.6 is used) KN