A plate is used as a tension member, to carry a deadload = 300 KN and live load of 260 KN. Steel used is A36, F, = 248 MPa, Fu = 400 MPa. If the width of the tension plate is 210 mm, determine: a) The thickness of the plate based on NSCP 2015 ASD, bult used is M20.------ b) The thickness of plate based on NSCP 2015 LRFD. Bolt used is M20.-------- 210 mm M20 bolts- -Tension Plate

A plate is used as a tension member, to carry a deadload = 300 KN and live load of 260 KN. Steel used is A36, F, = 248 MPa, Fu = 400 MPa. If the width of the tension plate is 210 mm, determine: a) The thickness of the plate based on NSCP 2015 ASD, bult used is M20.------ b) The thickness of plate based on NSCP 2015 LRFD. Bolt used is M20.-------- 210 mm M20 bolts- -Tension Plate

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

DO NO OWAVE www.oukpak.com F06 unic 30KN 150 KN 20KN 3m =30" SOLVE FOR ACL SUPPORT 2m HINGE REACTIONS LN DICATE THE DIRECTICNS e UNITC 20 A B im
A plate is used as a tension member, to carry a deadload = 300 KN and live load of 260 KN. Steel used is A36, Fy = 248 MPa, Fu = 400 MPa. If the width of the tension plate is 210 mm, determine: a) The thickness of the plate based on NSCP 2015 ASD, bult used is M20. b) The thickness of plate based on NSCP 2015 LRFD. Bolt used is M20. 210 mm Tension Plate M20 bolts
.
J 6 The cast iron bearing seat in the picture is bolted to the steel beam of the ceiling bracket and supports the gravity load. Use M20 coarse thread ISO class 8.8 bolts with a thickness of 3.4 mm The steel washers are placed under the bolt head and nut. The flange of this bracket is 20 mm thick, the shaft The elastic modulus of the bearing is 135 GPa. (a) Assuming this is a permanent joint and the fasteners are lubricated when assembled, find the required wrench torque. (b) If the gravity load is 15 kN, try to find the load factor n of the design.
A W14X120 is used as a tension member in atruss. The flanges of the member are connected to a gusset plate by 3/4 inch boltas shown below. Use A36 steel with Fy-36 ksi and Fu=58 ksi Determine the Yielding Capacity of the section based on LRFD (kips) Determine the Tensile Rupture capacity of the section based on LRFD Determine the Demand to Governing Capacity Ratio (based on yielding and rupture only) if the Demand load carried by the section are DL=200 kips LL=400 kips use LRFD Properties and Dimension Ag=35.30 in^2 x = 6.24 in ry= 3.74 in d=14.5 in tf=0.94 in bf=14.7 in tw=0.59 in k=1.54 d=14.5 Y k1=1.5 bf=14.7 tf-0.94 X -tw=0.59 H
Topic:Bolted Steel Connection - Civil Engineering *Use latest NSCP/NSCP 2015 formula to solve this problem The butt connection shows 8-22 mm dia. A325 bolts spaced as follows: S1 = 40 mm S3 = 50 mm t1 = 16 mm S2 = 80 mm S4 = 100 mm t2 = 12 mm Steel strength and stresses are: Fy = 248 MPa Fu = 400 MPa Allowable tensile stress on the gross area = 148 MPa Allowable tensile stress on the net area = 200 MPa Allowable shear stress on the net area = 120 MPa Allowable bolt shear stress, Fv = 120 MPa Bolt Hole diameter = 25 mm Questions: Calculate the allowable tensile load T, under the following conditions. a) Based on the gross area of the plate b) Based on the net area of the plate c) Based on block shear strength
A built-up section was made using PL414x12mm thk plates as shown in the figure below. It is pinned at both ends with additional support against weak axis at middle point. Assume A50 steel. PL414x12 DO Section W16x67 L x-axis a) Calculate moment of inertia at both axes in mm*. b) Determine the design compressive strength in kN if L-3m. c) Find the design compressive strength in kN if L=18m. Elevation y-axis
Q3-1 (Trusses), For the Figure shown below; 1 1. Find the forces in the members AB and AD of the truss and indicate whether it is in tension or 3m compression. 10KN 2. Read the following paragraph carefully then answer if it's TRUE or FALSE: The force in the member BC equal to zero? 3. Read the following paragraph carefully then CHOOSE THE CORRECT English Fried Safe 10KN 15 AN 3m 20 kN
Determine the load capacity of the angle LRFD. USE NSCP 2015.
The tension member is a PL 1⁄2 × 6. It is connected to a 3⁄8-inch-thick gusset plate with 7⁄8-inch-diameter bolts. Both components are of A242 steel. Note: A242 Fu = 70ksi dh = db + 1/16’’ Use: Consider deformation at the bolt hole what is the: minimum spacing as per AISC code provisions maximum spacing as per AISC code provisions minimum edge distance as per AISC code provisions maximum edge distance as per AISC code provisions
Select all zero-force members in the truss shown below. Check the box for zero- force members 3 m 3 m 12 m, 8 @ 1.5 m DE O LK ЕР O HF O BC BM EF OM CD BN LO O DK FI O co