The connection shown below uses 1-inch-diameter Group A bolts with the threads not in the shear plane. No slip is permitted. Both the tension member and the gusset plate are A36 steel. These bolts have not been added to distribute loads in the filler and two fillers are used. Use LRFD for solution. What is the design strength for tension on net area in kip? Express your answer in two decimal places.

The connection shown below uses 1-inch-diameter Group A bolts with the threads not in the shear plane. No slip is permitted. Both the tension member and the gusset plate are A36 steel. These bolts have not been added to distribute loads in the filler and two fillers are used. Use LRFD for solution. What is the design strength for tension on net area in kip? Express your answer in two decimal places.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For the tension member shown, compute the following. a. The tensile design strength. b. The allowable tensile strength. Weld PL 14 x 6 A36 steel
Determine the effective net area of the tension member shown in the figure. 000 3"3" L6 X 6 X 1/2 %-in. bolts Ciri2 ENGINEERING Section STEEL DESIGN 1.67"
The connection shown below uses 1-inch-diameter Group A bolts with the threads not in the shear plane. No slip is permitted. Both the tension member and the gusset plate are A36 steel. These bolts have not been added to distribute loads in the filler and two fillers are used. Use LRFD for solution. What is the design strength for slip-critical in kip?
The five-bolt connection shown must support an applied load of P = 371 kN. If the average shear stress in the bolts must be limited to 174 MPa, determine the minimum bolt diameter that may be used in the connection. Answer: d = i mm.
The tension member shown in the figure below is a ¹/2 x 10 plate of A36 steel: Fy = 36 ksi, Fu = 58 ksi. The connection is with 9/8-inch-diameter bolts. -→| 20 |einetein | 21 | 6 spaces @2" t = 1/2 in. Compute the nominal strength based on the net section. (Express your answer to three significant figures.) P₁ = kips
A double cover butt joint is shown in figure 2 below. If the steel is Grade S355JR and the bolts are M20 Grade 8.8 S, determine the strength of the connection. Assume the contact surface of the bolts are blast – cleaned with Class B coatings. The connection is required not to slip at serviceability. 80 120 80 80 120 80 -13 All dimensions are in mm Figure 2: Double cover butt joint. 300 O O O O o o O o o
PLEASE DOUBLE CHECK YOUR ANSWER Determine the maximum factored load that can be applied to the Tension member shown. The angle is ASTM A36. The diameter of the bolts is 1-in. CIVIL ENGINEERING STEEL DESIGN W12 x 16 4,-0.220 in -3.99 in 1=+=+=+= 3 in 3 in 3 in
The tension member shown in Figure 3.4-2 is a PL 5/8 x 10, and the steel is A36. The bolts are 7/8-inch in diameter. a. Determine the design strength for LRFD. b. Determine the allowable strength for ASD. | 2" +|+| in seinefrinehich 9 оо SO
7. Determine the design tensile strength of the plate (200 x 10 mm) connected to 12 mm thick gusset, using 24 mm bolts as shown below. Use A572M Grade 345 steel materials. 200 40 50 40 30 30 30 30 40
A PL3/8"X6" tension member is welded to a gusset plate as shown in the figure. The steel specification is ASTM A36. Assume that and compute the following: a) The design strength per LRFD b) The design strength per ASD PL ¾ x 6