Question Design an optimize welded connection with fillet weld and resist the dead load of 20 kips, live loads of 40 kips and wind loads of 10 kips. All steel is A36. Show your results on a sketch, complete with dimensions. 7 " 16 plate IE L6 X 4 X

Question Design an optimize welded connection with fillet weld and resist the dead load of 20 kips, live loads of 40 kips and wind loads of 10 kips. All steel is A36. Show your results on a sketch, complete with dimensions. 7 " 16 plate IE L6 X 4 X

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The pressure tank shown is fabricated from spirally-wrapped metal plates that are welded at the…

A: To Determine Largest allowable gauge pressure, P

Q: The welded girder shown in the accompanying illustration has an external shear VD = 300 k and VL =…

A: VD=300 kVL=350 k

Q: 1.A tension member is 25 mm thick plate as shown. The bolts are 20 mm. diameter high-strength bolts.…

A: Plate 130 mm x 25 mmbolt diameter, db = 20 mmA36 grade of steel:fy = 250 MPafy = 400 MPaTo find:a)…

Q: A C130x10 tension member is welded to a plate as shown in the figure. The channel is of Grade 350W…

Q: Determine the total LFRD design strength and the total ASD allowable strength of the 5/16 – in E70…

A: We will solve this question in step no. 2

Q: A UNS G10350 steel shaft, heat-treated to a minimum yield strength of 75 kpsi, has a diameter of 1-…

A: Solution:-UNS G10350Minimum yield strengthσymin=75kpsiShaft rotates n=613rpmd=2316P=53hpSafety…

Q: Calculate strength of single V butt joint to join 2 plates 300 x 16 mm with fy = 250 MPa. Assume…

Q: o normal temperatures but wet in-service conditions. Assume =0.95 and the geometry factor is CA=1.…

A: 1 Area of the plate Ag Ag = 4×10 = 40 in2for A36 grade steel fy =36000…

Q: Determine the design tensile strength, Pn, of a 3/8 x 6 plate tension member shown in the figure.…

A: 38×6 plateFu = Ultimate strength = 58 ksiFy = Yield strength = 36 ksi

Q: Select a double-angle tension member and design a welded connection to resist a dead load of 12 kips…

Q: Find out the strength and efficiency of a bolted lap joint .The bolts are of 30mm diameter, grade…

A: Diameter of bolt, d= 30 mmDiameter of bolt hole, do=30+2.5=32.5 mmFor bolts of grade 4.6 fub =400…

Q: The value (U) in (AISC) for welded member in tension load, if (2w > L>= 1.5w) where L: length of…

A: Given data Welded member Length of weld Distance between welds

Q: allowable

A: Block shear strength Agv =12in2×4 in= 4.00 in2Agv = 4.00 in2Ant = 12in10in = 5.0 in2Ubs = 1.0Rn…

Q: A WT7 x 41 bracket is connected to a W14 x 159 column with 5⁄16inch E70 fillet welds as shown in…

A: The load factor is the average load ratio to the highest demand. It depends on the value and the…

Q: EXERCISES Eleven sets of illustrations and the corresponding free-body diagrams of building-related…

Q: Iculate the maximum allowable force "P" that can be applied without causing the weld to Use the…

Q: PA PL ¹½/2 x 6 3″ 2 PL ¾/16 x 3 P

A: Tension member splice is made with weldsThe inner member is a and each outer member is a The live…

Q: P S S S

Q: Thursday Nov.24, 2020 Compute the design strength in tension, Pn, of an ASTM F1554 Gr. 36 % in…

A: Compute the design strength in tension Pn, of an ASTM F1554 Gr. 36% in diameter THREADED rod.Your…

Q: A PL 38 x 6 tension member is welded to a gusset plate as shown in figure. The steel is A36. PL % ×…

A: Note:- Hi! Thank you for the question, As per the honor code, we are allowed to answer three…

Q: A hanger is suspended from a plate that is welded to a wide flange beam as shown. The plate requires…

A: Hi! Thank you for the question As per the honor code, We’ll answer the first question since the…

Q: Design an optimize welded connection with fillet weld and E70XX electrodes to resist the dead load…

A: Dead Load = 20 kips Live Load = 40 kips Wind Load = 10kips Given L Section = 6" x 4" x (7/16)" The…

Q: a. Under a heavy vibrating loads it is possible that a fully tensioned bolt may come loose. As a…

A: Under heavy vibration or dynamic loading bolted connections and welded are not preferred. Because…

Q: The largest load P that can be applied is approximately equals:

A: Stress in rod ABσAB=PABA95103Kpa=PAB0.0007PAB=66.5KN

Q: Two 3/16" E70 fillet welds of 15 in. Iong are subjected to a load P. Using LRFD, compute the…

A: Answer (a) Minimum weld length requirement Minimum weld length may not be less than 4 times the…

Q: The details of an end bearing stiffener are shown in Figure . The stiffener plates are 9⁄16-inch…

A: A572 Grade 50:Fy=50 ksi Calculating the bearing strength: Apb=6-0.5×916×4=12.38 in2Rn=1.8 Fy Apb…

Q: Determine the design strength for C-shaped welds. USE E70 electrodes and 5/16" weld. 2011d

A: Given, E70 electrodes Weld thickness (w) = 5/16"

Q: 1½" 3"<3"→ -1½" 2" С7x 12.2 O O 2" t = ½"

A: Calculation Gross-section nominal strength; Pn = FyAg=50×(3.6)=180 kips Calculation of Net section…

Q: Material Strengths: Fy= 248 MPa, Fu= 400 MPa Method: Use ASD. A single angle L203X152X19 is welded…

Q: Using the elastic method, determine the maximum force to be resisted per inch by the fillet weld…

A: Consider the free body diagram as;

Q: he bolt is made of a material havin llowable shearing stress of 55.44 M

A: Given:- Allowable tensile stress=140.44MPa Allowable shearing stress=55.44MPa Axial load=17kN…

Q: A 21419x2 (3/8 in.SEPARATIOV), ASTM A36 „HAs ONE LINE OF &)孝n AND 25 is 25 O LENGTH. DIAMETER BOLTS…

Q: 4. Calculate the design strength (p.Pn) of W24X76 with length of 12 ft. and pinned ends. A572…

Q: tf Sec Ag tw W16x100 29.4 0.585 0.985 Bolt (7/8 in) A structural analysis was done for -1 the steel…

Q: Problem 7: The load that will be applied to the connection shown has a live load - to - dead load…

A: Note:- Hi! Thank you for the question, As per the honor code, we are allowed to answer three…

Q: A lap welded joint of A36 steel plates must hold a tensile load. The lower plate is .5 inches thick…

A: Lower plate tensile load = 0.5 inch thickWidth of lower plate = 7.7 inch wideUpper plate tensile…

Q: Q1 Two 3/16" E70 fillet welds of 15 in. long are subjected to a load P. Using LRFD, compute the…

A: Answer We are given size of weld (w)= 3/16 in Length of weld L = 15 in E 70 electrode

Q: Q3: Design 5/16-in SMAW fillet welds for the plate shown in figure below if A36 steel and E70…

A: Given data : design a 5/16 -in SMAW fillet welds for the plate ( for the given figure) use A36…

Q: A tension member splice is made with ¼/4-inch E70 fillet welds as shown in Figure 5. Each side of…

A: plate Member=2PL 7/16 x 4b=12 int=0.4375 inbase plate = PL 5/8 x 8t = 0.625 inE70 fillet weldweld…

Q: An I-section bracket is connected to the column as shown. The size of weld is 6 mm on web and 10 mm…

Q: For the tension member shown, determine the total service load (DL + LL) if LL = 4DL. Use A36 steel…

Q: A channel C250x37 mm section is welded to a 9 mm gusset plate. Welding is not permitted on the back…

A: Slot Weld : Slot weld is used to attach flat plates using one or more holes in the top part. To fuse…

Q: 7) The connection shows a PL10X200 loaded in tension and welded to a 10mm gusset plate. Calculate…

A: Answer Calculation of Design tensile strength in gross yielding We know that the Nominal tensile…

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Data Given

VIEW

Step 2: Load Calculation

VIEW

Step 3: Calculation of Length of weld

VIEW

Step 4: Sketch

VIEW

Solution

VIEW

Step by step

Solved in 5 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

S.design.
Use ASD to determine the width of the 5/8 inch thick A36 plate subjected to tension as shown below. The dead load effect is PD=85 kip while the live load effect is PL=80 kip. Two rows of 5/8 inch standard bolts will be used for the connection and the plate width can be manufactured in 1 inch increments. Assume that the larger connected plate does not fail. Consider the limit states of gross tensile yield and tensile rupture. Find the required tension strength, Pa, for the controlling ASD load combination. Determine the width necessary for the plate to resist gross tensile yield. Determine the width necessary for the plate to resist tensile rupture. Report the required plate width.
The equivalent stress for welding in given bracket connections would be if t = 5mm e i.e. Effective throat thickness of weld, use Fe410 steel and shop welding. P = 50 kN e = 200 mm h = 250 mm
Situation 1A - See Question Below Compute the maximum acceptable tensile SERVICE LOAD that may act on a single tee section that is connected to a gusset plate using welds 12 inches long, as shown in the figure. The service live load is three times the dead load. Use A992 steel. USE LRFD ONLY, no block shear will occur. A. Governing Ultimate Tensile Capacity based on Yielding of gross section Round your answer to 0 decimal places.
Use an elastic analysis and determine the maximum load in the weld (in kips per inch of length).
i need the answer quickly
Civil
Design a double angle tension member that is fillet welded to a gusset plate. Assume that the angles will be made from A36 steel, and the gusset plate from A572 Gr. 50 steel. Use 70ksi electrode. Design the system to resist a factored load of 200 kips. Check all applicable limit states that are possible. Provide your results on a sketch with standard weld symbols and details.
The tension member shown in the figure below is a ¹/2 x 10 plate of A36 steel: Fy = 36 ksi, Fu = 58 ksi. The connection is with 9/8-inch-diameter bolts. -→| 20 |einetein | 21 | 6 spaces @2" t = 1/2 in. Compute the nominal strength based on the net section. (Express your answer to three significant figures.) P₁ = kips
20. determine the capacity of the details shown below.A992: Fy=50ksi, Fu=65ksiA36: Fy=36ksi, Fu=58ksieffective bolt hole diameter = bolt hole + 1/16"beam properties: tw=0.38 in., bf=7.07 in., tf=0.63 in.Fexx=70ksit) what is the weld capacity perpedicular to the beam of the flange connection in kips? (2 decimal places)
Determine the size of the weld using E60 electrode. Dead Load = 38 kip and LL = 95 kips (Service Loads) 10 in- 10 in- -10 in W = ?
A C130x10 tension member is welded to a plate as shown in the figure. The channel is of Grade 350W steel. The channel is welded on both sides with 110 mm long fillet weld. Assume the weld does not govern the capacity, calculate the factored tension resistance of the channel. The tension resistance is not governed by the plate. C130 XI0