The steel pipe is filled with brass and subjected to a torsion T=34kNm.Determine each torsion value T¸ and T₁ taken by steel and brass.STake the shear modulus for steel G-80GPa and for brass G₁-40GPa.TITIT2 - steel1 - brass100cmT=34kNmcross-section of A-BOFd₁=4cmd₂=12cm

T = 34 kN- m = 34000 NLength L = 100 cmDiameter of brass db = 4 cm = 0.04 mOuter dia of steel do =…

The steel pipe is filled with brass and subjected to a torsion T-34kNm. Determine each torsion value T, and T₁ taken by steel and brass. Take the shear modulus for steel G§=80GPa and for brass G₁=40GPa.

The steel pipe is filled with brass and subjected to a torsion T-34kNm. Determine each torsion value T, and T₁ taken by steel and brass. Take the shear modulus for steel G§=80GPa and for brass G₁=40GPa.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

2. Determine the normal stress in members BD, AC, and BC in the truss shown. The cross- sectional area of each member is 1500 mm2. Indicate whether the stresses are tensile (T) or compressive (C). Use 2 decimal places in every solved value. 10 m 10 m 10 m K 6 т H 6 т 15° 15° 50 kN 40 kN E F 6 т C D б т A B
QU A composite beam is fabricated by bonding a steel bar and a brass bar and is subjected to the bending moment M = 200 N-m. Determine the maximum bending stress in the brass and steel. Given: E, =200 GPa, E, = 100 GPa Brass 20 }o | Jakrtal
Determine the normal stress in members BD, AC, and BCin the truss shown. The cross-sectional area of each member is 1500mm2. Indicate whether the stresses are tensile (T) or compressive (C). Use 2 decimal places in every solved value.
The compound shaft consists of a solid aluminum segment (1) and a hollow brass segment (2) that are connected at flange B and securely attached to rigid supports at A and C. Aluminum segment (1) has a diameter of 0.95 in., a length of L1 = 50 in., a shear modulus of 3800 ksi, and an allowable shear stress of 6.7 ksi. Brass segment (2) has an outside diameter of 0.85 in., a wall thickness of 0.13 in., a length of L2 = 38 in., a shear modulus of 6400 ksi, and an allowable shear stress of 8.0 ksi. Determine:(a) the allowable torque TB that can be applied to the compound shaft at flange B.(b) the magnitudes of the internal torques in segments (1) and (2).(c) the rotation angle of flange B (relative to support A) that is produced by the allowable torque TB.
The steel bars are firmly attached to rigid supports. Initially the temperature is 840F. Determine the stress in bars AC and CB when the temperature becomes -600F. Use E = 29 x 106 psi and α = 6.50 x 10-6/ 0F.
The pin-connected assembly consists of aluminum rods (1) and (2) and steel rod (3). The aluminum rods each have a diameter of 11 mm and an elastic modulus of E = 78 GPa. The steel rod has a diameter of 16 mm and an elastic modulus of E = 200 GPa. Assumea = 4.1 m, b= 1.2 m, and c= 1.2 m. What is the magnitude of load P that is necessary to displace point A 12 mm to the left? a (1) (3) A B (2) Answer: P = i kN
A steel rectangular block is subjected to a uniform stress of o = 150 MPa acting on all faces. The dimensions of the block are as follows: L_x=100 mm,L_y=30 mm,L_z=40 mm. Determine the change in length along the y-axis. Use E = 200 GPa and v 0.3. Note that ɛ_0=-o/E(1+2v). A -0.03 mm -0.015 mm -0.009 mm -0.012 mm
When the temperature is at 30°C, the steel pipe fits snugly between the two fuel tanks. When fuel flows through the pipe, it causes the temperature to vary along the pipe as T = (3x² 20x + 120)°C. Calculate the normal stress developed in the pipe. Assume each tank provides a rigid support at A and B. a=12X10-6/°C - 150 mm 10 mm- Section a - a -6 m a a B
Load P is applied to joint D and the temperature increases by 50 °F. There are two steel (E = 29*10^6 psi; a = 6.5*10^-6/°F) AD and DC and a bronze (E = 16*10^6 psi; a = 9*10^-6/°F) BD with a length of 50 inches. Each bar is a 0.75 inch diameter. Find the deformation of every rod, the displacement at D, and the stress in each rod.
A magnesium-alloy rod (E = 6.5 x 10 ksi) of Prob. 3.4-6. diameter d 1 in. is encased by a brass tube (E 15 x 10 ksi) with outer diameter d. = 1.5 in.; both have length. L = 20 in. An axial load P = 10 kips is applied to the resulting bimetallic rod. (a) Determine the normal stresses and , in each material, assuming that the magnesium rod and brass tube are securely bonded to each other. (b) Determine the elongation of the bimetallic rod. P