The Q = 0.85 m/s the length of pipes 1, 2, 3, 4 and 5 are 1000m,500m, 600m, 800m and 700m respectively. The total head loss in the system is 10 m. and the diameter for pipes 1, 2, 3 and 5 are 90 cm, 50 cm, 40 cm, and 75 cm. respectively. Determine the diameter in pipe 4 if the coefficient of friction in each pipe is 0.020. Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: mm Decimal Places required in the final answer: 3 3 4

The Q = 0.85 m/s the length of pipes 1, 2, 3, 4 and 5 are 1000m,500m, 600m, 800m and 700m respectively. The total head loss in the system is 10 m. and the diameter for pipes 1, 2, 3 and 5 are 90 cm, 50 cm, 40 cm, and 75 cm. respectively. Determine the diameter in pipe 4 if the coefficient of friction in each pipe is 0.020. Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: mm Decimal Places required in the final answer: 3 3 4

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

L = 900m D=35cm L=600m L=900m D=75cm D=60cm L=600m D=30cm L=900m D=40cm A flow rate of 0.5 m³/s is branched into three pipes and then rejoined in the concrete parallel pipes as shown in the figure below. Find the head of loss between point A and point B. Here, the coefficient of friction loss in all tubes is 0.03.
Elev A Water Elev C Elev B Water flows from Reservoir A (Elev 138 ft.) to a turbine (Elev 75 ft.) then discharges into tailtrace B (Elev 26 ft.) as shown. The head loss from (A) to (1) is 4 times the velocity head in the pipe, and the head loss from (2) to (b) is 0.96 times the velocity head in the pipe. If the flow rate in the pipe is 34 ft3/s, diameter of all pipes is 26 in, calculate the horsepower generated by the turbine. Use 1 hp = 550 lb-ft/s. Round off to the nearest whole number.
1. Water flows through a horizontal, 0.5-m-diameter pipe at a rate of 0.9 m³/s (Figure below). It is ejected from the pipe through a 0.25-m-diameter nozzle. Determine the force (F) that holds the nozzle in place if the water pressure in the pipe just upstream of the nozzle is 283 kN/m² (kPa). F Fpl V₁. in F H Vout 2. Given H= 1.8 m & D = 0.2 m through the hole in the open top container. Determine the head losses through the tank outlet if the exit discharge were 0.163 m³/sec.
14. Water is pumped from one tank to another through a 0.100 m smooth plastic tube. The flow rate is 0.200 m³/s. The head loss due to major and minor friction losses is given by the equation, h₁ = 12.0 2g V 25 m Pump Determine the pump head. Also determine the shaft work done by the pump.
a. Determine the velocity of flow in the pipe in m/s. b. Determine the discharge Q in m^3/s. c. How many meters above the center of the pipe will water stand in piezometer tube 3? d.
Two pipes A and B are connected in parallel between two points M and N as shown in figure. Pipe A is 80 mm diameter, 900 m long and its friction factor is 0.015. Pipe B is of 100 mm diameter, 700 m long and its friction factor is 0.018. A total discharge of 0.030 m³/s is entering the parallel pipes through the division at M. Calculate the discharge in the two pipes A and B. M = 0.015 A fA 80 mm dia, 900 m 100 mm dia, 700 m B fB = = 0.018 N
Question 2: A pipeline carries a pumped flow of 0.05 m/s. The line contains three 90 degree bends (K=0.9), a gate valve (K=0.4), and a swing check valve (K=0.6). Select an internal diameter between 10 cm to 90 cm for steel pipe (e= 0.00015 in, 0.00381 mm). Determine the total head loss if the lengt of the straight pipe is 300 m.
A 30 cm diameter pipe is connected by a reducer to a 10 cm diameter pipe. Points 1 (on the 30 cm diam.) and 2 (on the 10 cm diam.) are along the same elevation. The pressure at 1 is 250 KPa. The flow is 50 liters per second and the energy lost between 1 and 2 is equivalent to 20 KPa. Compute the pressure at 2 if the liquid flowing has a specific gravity of 1.30.
Do it
8.4
For the pipe networks shown, the flow of water from reservoir A to the junction is 0.035 cu.m.per second. a) Determine Q2, Q3 b) Determine the head loss from A to B
Determine the friction loss if the friction factor is 0.4 and velocity of the flow is 40 m per sec. Given length of the pipe is 20m, inner diameter 0.3m. Use friction loss formula. Using the calculated friction loss, solve for the ffg: a. What is the pressure drop due to the Bernoulli effect as the water goes into a 3.00-cm-diameter nozzle froma 9.00-cm-diameter fire hose while carrying a flow of 40.0 L/s? b. To what maximum height above the nozzle can this water rise? (To actual height will be significantly smaller due to air resistance.)